patch-1.3.22 linux/Documentation/networking/arcnet-jumpers.txt
Next file: linux/Documentation/networking/arcnet.txt
Previous file: linux/Documentation/modules.txt
Back to the patch index
Back to the overall index
- Lines: 1912
- Date:
Wed Jul 12 07:53:14 1995
- Orig file:
v1.3.21/linux/Documentation/networking/arcnet-jumpers.txt
- Orig date:
Thu Jan 1 02:00:00 1970
diff -u --recursive --new-file v1.3.21/linux/Documentation/networking/arcnet-jumpers.txt linux/Documentation/networking/arcnet-jumpers.txt
@@ -0,0 +1,1911 @@
+
+-----------------------------------------------------------------------------
+This file is a supplement to README.arcnet. Please read that for general
+driver configuration help.
+-----------------------------------------------------------------------------
+
+Because so many people (myself included) seem to have obtained ARCnet cards
+without manuals, this will be a quick listing of all jumper settings I can
+find. Please e-mail [email protected] with any settings for
+your particular card.
+
+Even if your ARCnet model isn't listed, but has the same jumpers, please
+e-mail me to say so.
+
+If your model isn't listed, and has different settings, PLEASE PLEASE tell
+me. I had to figure mine out without the manual, and it WASN'T FUN!
+
+Cards Listed in this file (in this order, mostly):
+
+ Manufacturer Model # Bits
+ ------------ ------- ----
+ SMC PC100 8
+ SMC PC110 8
+ SMC PC120 8
+ SMC PC130 8
+ SMC PC270E 8
+ SMC PC500 16
+ SMC PC500Longboard 16
+ SMC PC550Longboard 16
+ SMC PC600 16
+ SMC? LCS-8830-T 16?
+ Puredata PDI507 16
+ CNet Tech CN120-Series 8
+ CNet Tech CN160-Series 16
+ No Name -- 8/16
+ No Name Taiwan R.O.C(?) 8
+ Tiara Tiara Lancard(?)
+
+
+** SMC = Standard Microsystems Corp.
+** CNet Tech = CNet Technology, Inc.
+
+The model # is listed right above specifics for that card. Don't forget to
+read "quick briefing" first, since it applies to all ARCnets.
+
+
+Unclassified Stuff
+------------------
+ - Please send any other information you can find.
+
+ - And some unknowns (other info is welcome!):
+ From: [email protected] (Timo Hilbrink)
+ To: [email protected] (Avery Pennarun)
+ Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT)
+ Reply-To: [email protected]
+
+ [...parts deleted...]
+
+ About the jumpers: On my PC130 there is one more jumper, located near the
+ cable-connector and it's for changing to star or bus topology;
+ closed: star - open: bus
+ On the PC500 are some more jumper-pins, one block labled with RX,PDN,TXI
+ and another with ALE,LA17,LA18,LA19 these are undocumented..
+
+ [...more parts deleted...]
+
+ --- CUT ---
+
+
+Quick Briefing:
+---------------
+
+All ARCnet cards should have a total of four different settings:
+
+ - the I/O address: this is the "port" your ARCnet card is on. Probed
+ values, as of v0.14, are only from 0x200 through 0x3F0. (If your card
+ has additional ones, which is possible, please tell me.) This should not
+ be the same as any other device on your system. According to a doc I
+ got from Novell, MS Windows prefers values of 0x300 or more, eating
+ netconnections on my system otherwise.
+ - Avery's favourite: 0x300.
+
+ - the IRQ: on 8-bit cards, it might be 2 (9), 3, 4, 5, or 7.
+ on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15. Make
+ sure this is different from any other card on your system. Note that
+ IRQ2 is the same as IRQ9, as far as Linux is concerned.
+ - Avery's favourite: IRQ2.
+
+ - the memory address: Unlike most cards, ARCnets use "shared memory" for
+ copying buffers around. Make SURE it doesn't conflict with any other
+ used memory in your system!
+ A0000 - VGA graphics memory (ok if you don't have VGA)
+ B0000 - Monochrome text mode
+ C0000 \ One of these is your VGA BIOS - usually C0000.
+ E0000 /
+ F0000 - System BIOS
+
+ Anything less than 0xA0000 is, well, a BAD idea since it isn't above
+ 640k.
+ - Avery's favourite: 0xD0000
+
+ - the station address: Every ARCnet card has its own "unique" network
+ address from 0 to 255. Unlike ethernet, you can set this address
+ yourself. Since it's only 8 bits, you can only have 254 ARCnet cards on
+ a network. DON'T use 0 or 255, since these are reserved. (although neat
+ stuff will probably happen if you DO use them). By the way, if you
+ haven't already guessed, don't set this the same as any other ARCnet on
+ your network!
+ - Avery's favourite: 3 and 4. Not that it matters.
+
+
+** Standard Microsystems Corp (SMC) **
+PC100, PC110, PC120, PC130 (8-bit cards)
+PC500, PC600 (16-bit cards)
+---------------------------------
+ - mainly from Avery Pennarun <[email protected]>. Values depicted are
+ from Avery's setup.
+ - special thanks to Timo Hilbrink <[email protected]> for noting that PC120,
+ 130, 500, and 600 all have the same switches as Avery's PC100.
+ PC500/600 have several extra, undocumented pins though. (?)
+ - PC110 settings were verified by Stephen A. Wood <[email protected]>
+ - On the other hand, John Edward Bauer <[email protected]> said
+ the PC110 settings are all wrong. In his case, you need to switch all
+ the 1's with 0's. If you're having problems, try that.
+ - Also, the JP- and S-numbers probably don't match your card exactly. Try
+ to find jumpers/switches with the same number of settings - it's
+ probably more reliable.
+
+
+ JP5 [|] : : : :
+(IRQ Setting) IRQ2 IRQ3 IRQ4 IRQ5 IRQ7
+ Put exactly one jumper on exactly one set of pins.
+
+ 1 2 3 4 5 6 7 8 9 10
+ S1 /----------------------------------\
+(I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 |
+ addresses) \----------------------------------/
+ |--| |--------| |--------|
+ (a) (b) (m)
+
+ a: The first digit of the I/O address.
+ Setting Value
+ ------- -----
+ 00 0
+ 01 1
+ 10 2
+ 11 3
+
+ b: The second digit of the I/O address.
+ Setting Value
+ ------- -----
+ 0000 0
+ 0001 1
+ 0010 2
+ ... ...
+ 1110 E
+ 1111 F
+
+ The I/O address is in the form ab0. For example, if
+ a is 0x2 and b is 0xE, the address will be 0x2E0.
+
+ DO NOT SET THIS LESS THAN 0x200!!!!!
+
+
+ m: The first digit of the memory address.
+ Setting Value
+ ------- -----
+ 0000 0
+ 0001 1
+ 0010 2
+ ... ...
+ 1110 E
+ 1111 F
+
+ The memory address is in the form m0000. For example, if
+ m is D, the address will be 0xD0000.
+
+ DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000!
+
+ 1 2 3 4 5 6 7 8
+ S2 /--------------------------\
+(Station Address) | 1 1 0 0 0 0 0 0 |
+ \--------------------------/
+
+ Setting Value
+ ------- -----
+ 00000000 00
+ 10000000 01
+ 01000000 02
+ ...
+ 01111111 FE
+ 11111111 FF
+
+ Note that this is binary with the digits reversed!
+
+ DO NOT SET THIS TO 0 OR 255 (0xFF)!
+
+
+*****************************************************************************
+
+** Standard Microsystems Corp (SMC) **
+PC130E/PC270E (8-bit cards)
+---------------------------
+ - from Juergen Seifert <[email protected]>
+
+
+STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET(R)-PC130E/PC270E
+===============================================================
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the following Original SMC Manual
+
+ "Configuration Guide for
+ ARCNET(R)-PC130E/PC270
+ Network Controller Boards
+ Pub. # 900.044A
+ June, 1989"
+
+ARCNET is a registered trademark of the Datapoint Corporation
+SMC is a registered trademark of the Standard Microsystems Corporation
+
+The PC130E is an enhanced version of the PC130 board, is equipped with a
+standard BNC female connector for connection to RG-62/U coax cable.
+Since this board is designed both for point-to-point connection in star
+networks and for connection to bus networks, it is downwardly compatible
+with all the other standard boards designed for coax networks (that is,
+the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and
+PC200 bus topology boards).
+
+The PC270E is an enhanced version of the PC260 board, is equipped with two
+modular RJ11-type jacks for connection to twisted pair wiring.
+It can be used in a star or a daisy-chained network.
+
+
+ 8 7 6 5 4 3 2 1
+ ________________________________________________________________
+ | | S1 | |
+ | |_________________| |
+ | Offs|Base |I/O Addr |
+ | RAM Addr | ___|
+ | ___ ___ CR3 |___|
+ | | \/ | CR4 |___|
+ | | PROM | ___|
+ | | | N | | 8
+ | | SOCKET | o | | 7
+ | |________| d | | 6
+ | ___________________ e | | 5
+ | | | A | S | 4
+ | |oo| EXT2 | | d | 2 | 3
+ | |oo| EXT1 | SMC | d | | 2
+ | |oo| ROM | 90C63 | r |___| 1
+ | |oo| IRQ7 | | |o| _____|
+ | |oo| IRQ5 | | |o| | J1 |
+ | |oo| IRQ4 | | STAR |_____|
+ | |oo| IRQ3 | | | J2 |
+ | |oo| IRQ2 |___________________| |_____|
+ |___ ______________|
+ | |
+ |_____________________________________________|
+
+Legend:
+
+SMC 90C63 ARCNET Controller / Transceiver /Logic
+S1 1-3: I/O Base Address Select
+ 4-6: Memory Base Address Select
+ 7-8: RAM Offset Select
+S2 1-8: Node ID Select
+EXT Extended Timeout Select
+ROM ROM Enable Select
+STAR Selected - Star Topology (PC130E only)
+ Deselected - Bus Topology (PC130E only)
+CR3/CR4 Diagnostic LEDs
+J1 BNC RG62/U Connector (PC130E only)
+J1 6-position Telephone Jack (PC270E only)
+J2 6-position Telephone Jack (PC270E only)
+
+Setting one of the switches to Off/Open means "1", On/Closed means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in group S2 are used to set the node ID.
+Each node attached to the network must have an unique node ID which
+must be diffrent from 0.
+Switch 1 serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+ Switch | Value
+ -------|-------
+ 1 | 1
+ 2 | 2
+ 3 | 4
+ 4 | 8
+ 5 | 16
+ 6 | 32
+ 7 | 64
+ 8 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 8 7 6 5 4 3 2 1 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The first three switches in switch group S1 are used to select one
+of eight possible I/O Base addresses using the followig table
+
+
+ Switch | Hex I/O
+ 1 2 3 | Address
+ -------|--------
+ 0 0 0 | 260
+ 0 0 1 | 290
+ 0 1 0 | 2E0 (Manufactor's default)
+ 0 1 1 | 2F0
+ 1 0 0 | 300
+ 1 0 1 | 350
+ 1 1 0 | 380
+ 1 1 1 | 3E0
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The memory buffer requires 2K of a 16K block of RAM. The base of this
+16K block can be located in any of eight positions.
+Switches 4-6 of switch group S1 select the Base of the 16K block.
+Within that 16K address space, the buffer may be assigned any one of four
+positions, determined by the offset, switches 7 and 8 of group S1.
+
+ Switch | Hex RAM | Hex ROM
+ 4 5 6 7 8 | Address | Address *)
+ -----------|---------|-----------
+ 0 0 0 0 0 | C0000 | C2000
+ 0 0 0 0 1 | C0800 | C2000
+ 0 0 0 1 0 | C1000 | C2000
+ 0 0 0 1 1 | C1800 | C2000
+ | |
+ 0 0 1 0 0 | C4000 | C6000
+ 0 0 1 0 1 | C4800 | C6000
+ 0 0 1 1 0 | C5000 | C6000
+ 0 0 1 1 1 | C5800 | C6000
+ | |
+ 0 1 0 0 0 | CC000 | CE000
+ 0 1 0 0 1 | CC800 | CE000
+ 0 1 0 1 0 | CD000 | CE000
+ 0 1 0 1 1 | CD800 | CE000
+ | |
+ 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
+ 0 1 1 0 1 | D0800 | D2000
+ 0 1 1 1 0 | D1000 | D2000
+ 0 1 1 1 1 | D1800 | D2000
+ | |
+ 1 0 0 0 0 | D4000 | D6000
+ 1 0 0 0 1 | D4800 | D6000
+ 1 0 0 1 0 | D5000 | D6000
+ 1 0 0 1 1 | D5800 | D6000
+ | |
+ 1 0 1 0 0 | D8000 | DA000
+ 1 0 1 0 1 | D8800 | DA000
+ 1 0 1 1 0 | D9000 | DA000
+ 1 0 1 1 1 | D9800 | DA000
+ | |
+ 1 1 0 0 0 | DC000 | DE000
+ 1 1 0 0 1 | DC800 | DE000
+ 1 1 0 1 0 | DD000 | DE000
+ 1 1 0 1 1 | DD800 | DE000
+ | |
+ 1 1 1 0 0 | E0000 | E2000
+ 1 1 1 0 1 | E0800 | E2000
+ 1 1 1 1 0 | E1000 | E2000
+ 1 1 1 1 1 | E1800 | E2000
+
+*) To enable the 8K Boot PROM install the jumper ROM.
+ The default is jumper ROM not installed.
+
+
+Setting the Timeouts and Interrupt
+----------------------------------
+
+The jumpers labeled EXT1 and EXT2 are used to determine the timeout
+parameters. These two jumpers are normally left open.
+Refer to the COM9026 Data Sheet for alternate configurations.
+
+To select a hardware interrupt level set one (only one!) of the jumpers
+IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The Manufactor's default is IRQ2.
+
+
+Configuring the PC130E for Star or Bus Topology
+-----------------------------------------------
+
+The single jumper labeled STAR is used to configure the PC130E board for
+star or bus topology.
+When the jumper is installed, the board may be used in a star network, when
+it is removed, the board can be used in a bus topology.
+
+
+Diagnostic LEDs
+---------------
+
+Two diagnostic LEDs are visible on the rear bracket of the board.
+The green LED monitors the network activity: the red one shows the
+board activity:
+
+ Green | Status Red | Status
+ -------|------------------- ---------|-------------------
+ on | normal activity flash/on | data transfer
+ blink | reconfiguration off | no data transfer;
+ off | defectiv board or | incorect memory or
+ | node ID is zero | I/O address
+
+
+*****************************************************************************
+
+** Standard Microsystems Corp (SMC) **
+PC500/PC550 Long Board (16-bit cards)
+-------------------------------------
+ - from Juergen Seifert <[email protected]>
+
+
+STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET-PC500/PC550 Long Board
+=====================================================================
+
+Note: There is another Version of the PC500 called Short Version, which
+ is different in hard- and software! The most important differences
+ are:
+ - The long board has no Shared memory
+ - On the long board the selection of the interrupt is done by binary
+ coded switch, on the short board directly by jumper.
+
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the following Original SMC Manual
+
+ "Configuration Guide for
+ SMC ARCNET-PC500/PC550
+ Series Network Controller Boards
+ Pub. # 900.033 Rev. A
+ November, 1989"
+
+ARCNET is a registered trademark of the Datapoint Corporation
+SMC is a registered trademark of the Standard Microsystems Corporation
+
+The PC500 is equipped with a standard BNC female connector for connection
+to RG-62/U coax cable.
+The board is designed both for point-to-point connection in star networks
+and for connection to bus networks.
+
+The PC550 is equipped with two modular RJ11-type jacks for connection
+to twisted pair wiring.
+It can be used in a star or a daisy-chained network.
+
+ 1
+ 0 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1
+ ____________________________________________________________________
+ < | SW1 | | SW2 | |
+ > |_____________________| |_____________| |
+ < IRQ |I/O Addr |
+ > ___|
+ < CR4 |___|
+ > CR3 |___|
+ < ___|
+ > N | | 8
+ < o | | 7
+ > d | S | 6
+ < e | W | 5
+ > A | 3 | 4
+ < d | | 3
+ > d | | 2
+ < r |___| 1
+ > |o| _____|
+ < |o| | J1 |
+ > 3 1 JP6 |_____|
+ < |o|o| JP2 | J2 |
+ > |o|o| |_____|
+ < 4 2__ ______________|
+ > | | |
+ <____| |_____________________________________________|
+
+Legend:
+
+SW1 1-6: I/O Base Address Select
+ 7-10: Interrupt Select
+SW2 1-6: Reserved for Future Use
+SW3 1-8: Node ID Select
+JP2 1-4: Extended Timeout Select
+JP6 Selected - Star Topology (PC500 only)
+ Deselected - Bus Topology (PC500 only)
+CR3 Green Monitors Network Activity
+CR4 Red Monitors Board Activity
+J1 BNC RG62/U Connector (PC500 only)
+J1 6-position Telephone Jack (PC550 only)
+J2 6-position Telephone Jack (PC550 only)
+
+Setting one of the switches to Off/Open means "1", On/Closed means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in group SW3 are used to set the node ID. Each node
+attached to the network must have an unique node ID which must be
+diffrent from 0.
+Switch 1 serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Value
+ -------|-------
+ 1 | 1
+ 2 | 2
+ 3 | 4
+ 4 | 8
+ 5 | 16
+ 6 | 32
+ 7 | 64
+ 8 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 8 7 6 5 4 3 2 1 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The first six switches in switch group SW1 are used to select one
+of 32 possible I/O Base addresses using the followig table
+
+ Switch | Hex I/O
+ 6 5 4 3 2 1 | Address
+ -------------|--------
+ 0 1 0 0 0 0 | 200
+ 0 1 0 0 0 1 | 210
+ 0 1 0 0 1 0 | 220
+ 0 1 0 0 1 1 | 230
+ 0 1 0 1 0 0 | 240
+ 0 1 0 1 0 1 | 250
+ 0 1 0 1 1 0 | 260
+ 0 1 0 1 1 1 | 270
+ 0 1 1 0 0 0 | 280
+ 0 1 1 0 0 1 | 290
+ 0 1 1 0 1 0 | 2A0
+ 0 1 1 0 1 1 | 2B0
+ 0 1 1 1 0 0 | 2C0
+ 0 1 1 1 0 1 | 2D0
+ 0 1 1 1 1 0 | 2E0 (Manufactor's default)
+ 0 1 1 1 1 1 | 2F0
+ 1 1 0 0 0 0 | 300
+ 1 1 0 0 0 1 | 310
+ 1 1 0 0 1 0 | 320
+ 1 1 0 0 1 1 | 330
+ 1 1 0 1 0 0 | 340
+ 1 1 0 1 0 1 | 350
+ 1 1 0 1 1 0 | 360
+ 1 1 0 1 1 1 | 370
+ 1 1 1 0 0 0 | 380
+ 1 1 1 0 0 1 | 390
+ 1 1 1 0 1 0 | 3A0
+ 1 1 1 0 1 1 | 3B0
+ 1 1 1 1 0 0 | 3C0
+ 1 1 1 1 0 1 | 3D0
+ 1 1 1 1 1 0 | 3E0
+ 1 1 1 1 1 1 | 3F0
+
+
+Setting the Interrupt
+---------------------
+
+Switches seven through ten of switch group SW1 are used to select the
+interrupt level. The interrupt level is binary coded, so selections
+from 0 to 15 would be possible, but only the following eight values will
+be supported: 3, 4, 5, 7, 9, 10, 11, 12.
+
+ Switch | IRQ
+ 10 9 8 7 |
+ ---------|--------
+ 0 0 1 1 | 3
+ 0 1 0 0 | 4
+ 0 1 0 1 | 5
+ 0 1 1 1 | 7
+ 1 0 0 1 | 9 (=2) (default)
+ 1 0 1 0 | 10
+ 1 0 1 1 | 11
+ 1 1 0 0 | 12
+
+
+Setting the Timeouts
+--------------------
+
+The two jumpers JP2 (1-4) are used to determine the timeout parameters.
+These two jumpers are normally left open.
+Refer to the COM9026 Data Sheet for alternate configurations.
+
+
+Configuring the PC500 for Star or Bus Topology
+----------------------------------------------
+
+The single jumper labeled JP6 is used to configure the PC500 board for
+star or bus topology.
+When the jumper is installed, the board may be used in a star network, when
+it is removed, the board can be used in a bus topology.
+
+
+Diagnostic LEDs
+---------------
+
+Two diagnostic LEDs are visible on the rear bracket of the board.
+The green LED monitors the network activity: the red one shows the
+board activity:
+
+ Green | Status Red | Status
+ -------|------------------- ---------|-------------------
+ on | normal activity flash/on | data transfer
+ blink | reconfiguration off | no data transfer;
+ off | defectiv board or | incorect memory or
+ | node ID is zero | I/O address
+
+
+*****************************************************************************
+
+** Possibly SMC **
+LCS-8830-T (16-bit card)
+------------------------
+ - from Mathias Katzer <[email protected]>
+
+This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC,
+nowhere else, not even on the few xeroxed sheets from the manual).
+
+SMC Arcnet Board Type LCS-8830-T
+
+ ------------------------------------
+ | |
+ | JP3 88 8 JP2 |
+ | ##### | \ |
+ | ##### ET1 ET2 ###|
+ | 8 ###|
+ | U3 SW 1 JP0 ###| Phone Jacks
+ | -- ###|
+ | | | |
+ | | | SW2 |
+ | | | |
+ | | | ##### |
+ | -- ##### #### BNC Connector
+ | ####
+ | 888888 JP1 |
+ | 234567 |
+ -- -------
+ |||||||||||||||||||||||||||
+ --------------------------
+
+
+SW1: DIP-Switches for Station Address
+SW2: DIP-Switches for Memory Base and I/O Base addresses
+
+JP0: If closed, internal termination on (default open)
+JP1: IRQ Jumpers
+JP2: Boot-ROM enabled if closed
+JP3: Jumpers for respsonse timeout
+
+U3: Boot-ROM Socket
+
+
+ET1 ET2 Response Time Idle Time Reconfiguration Time
+
+ 78 86 840
+ X 285 316 1680
+ X 563 624 1680
+ X X 1130 1237 1680
+
+(X means closed jumper)
+
+(DIP-Switch downwards means "0")
+
+The station address is binary-coded with SW1.
+
+The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
+
+Switches Base
+678 Address
+000 260-26f
+100 290-29f
+010 2e0-2ef
+110 2f0-2ff
+001 300-30f
+101 350-35f
+011 380-38f
+111 3e0-3ef
+
+
+DIP Switches 1-5 of SW2 encode the RAM and ROM Adress Range:
+
+Switches Ram Rom
+12345 Adress Range Address Range
+00000 C:0000-C:07ff C:2000-C:3fff
+10000 C:0800-C:0fff
+01000 C:1000-C:17ff
+11000 C:1800-C:1fff
+00100 C:4000-C:47ff C:6000-C:7fff
+10100 C:4800-C:4fff
+01100 C:5000-C:57ff
+11100 C:5800-C:5fff
+00010 C:C000-C:C7ff C:E000-C:ffff
+10010 C:C800-C:Cfff
+01010 C:D000-C:D7ff
+11010 C:D800-C:Dfff
+00110 D:0000-D:07ff D:2000-D:3fff
+10110 D:0800-D:0fff
+01110 D:1000-D:17ff
+11110 D:1800-D:1fff
+00001 D:4000-D:47ff D:6000-D:7fff
+10001 D:4800-D:4fff
+01001 D:5000-D:57ff
+11001 D:5800-D:5fff
+00101 D:8000-D:87ff D:A000-D:bfff
+10101 D:8800-D:8fff
+01101 D:9000-D:97ff
+11101 D:9800-D:9fff
+00011 D:C000-D:c7ff D:E000-D:ffff
+10011 D:C800-D:cfff
+01011 D:D000-D:d7ff
+11011 D:D800-D:dfff
+00111 E:0000-E:07ff E:2000-E:3fff
+10111 E:0800-E:0fff
+01111 E:1000-E:17ff
+11111 E:1800-E:1fff
+
+
+*****************************************************************************
+
+** PureData Corp **
+PDI507 (16-bit card)
+--------------------
+ - from Mark Rejhon <[email protected]> (slight modifications by
+ Avery)
+ - Send questions/suggestions/etc about this text to Mark.
+
+Jumpers:
+
+ There is a jumper array at the bottom of the card, near the edge
+ connector. This array is labelled J1. They control the IRQs and
+ something else. Put only one jumper on the IRQ pins.
+
+ IRQ2 - Use IRQ 2 (same as IRQ 9 as far as software is concerned)
+ IRQ3 - Use IRQ 3 (used by COM2 or COM4 serial port if either exists)
+ IRQ4 - Use IRQ 4 (used by COM1 or COM3 serial port if either exists)
+ IRQ5 - Use IRQ 5 (used by LPT2 parallel port if one exists)
+ IRQ6 - Use IRQ 6 (used by Floppy Disk Controller if one exists)
+ IRQ7 - Use IRQ 7 (used by LPT1 parallel port if one exists)
+
+[Avery's note: This "unknown" set of two jumpers appears to be on all
+ARCnet cards by SMC as well. Putting jumpers on them seems to affect the
+status register, but only for the two "reserved" bits, ETS1 and ETS2. Any
+further information is welcome.]
+
+ ET1 - What is this? (Not tested, no jumper put on it)
+ ET2 - What is this? (Not tested, no jumper put on it)
+
+ There is a J2 jumper on two pins. A jumper should be put on them,
+ since it was already there when I got the card. I don't know what
+ this jumper is for though.
+
+ There is a two-jumper array for J3. I don't know what it is for,
+ but there were already two jumpers on it when I got the card. It's
+ a six pin grid in a two-by-three fashion. The jumpers were
+ configured as follows:
+
+ .-------.
+ o | o o |
+ :-------: ------> Accessible end of card with connectors
+ o | o o | in this direction ------->
+ `-------'
+
+ There is also a J4 jumper on two pins. A jumper should be put on
+ them, since it was already there when I got the card. I don't know
+ what this jumper is for though.
+
+
+DIP Switches:
+
+ The dipswitches accessible on the accessible end of the card while
+ it is installed, is used to set the arcnet address. There are 8
+ switches. Use an address from 1 to 254.
+
+ Switch No.
+ 12345678 Arcnet address
+ -----------------------------------------
+ 00000000 FF (Don't use this!)
+ 00000001 FE
+ 00000010 FD
+ ....
+ 11111101 2
+ 11111110 1
+ 11111111 0 (Don't use this!)
+
+ There is another dipswitch array of 8 switches at the top of the
+ card. There are five labelled MS0-MS4 which seem to control the
+ memory address, and another three labelled IO0-IO2 which seem to
+ control the base I/O address of the card.
+
+ This was difficult to test by trial and error, and the I/O addresses
+ are in a weird order. This was tested by setting the DIP switches,
+ rebooting the computer, and attempting to load ARCETHER at various
+ addresses (mostly between 0x200 and 0x400). The address that caused
+ the red transmit LED to blink, is the one that I thought works.
+
+ Also, the address 0x3D0 seem to have a special meaning, since the
+ ARCETHER packet driver loaded fine, but without the red LED
+ blinking. I don't know what 0x3D0 is for though. I recommend using
+ an address of 0x300 since Windows may not like addresses below
+ 0x300.
+
+ IO Switch No.
+ 210 I/O address
+ -------------------------------
+ 111 0x260
+ 110 0x290
+ 101 0x2E0
+ 100 0x2F0
+ 011 0x300
+ 010 0x350
+ 001 0x380
+ 000 0x3E0
+
+ The memory switches set a reserved address space of 0x1000 bytes
+ (0x100 segment units, or 4k). For example if I set an address of
+ 0xD000, it will use up addresses 0xD000 to 0xD100.
+
+ The memory switches were tested by booting using QEMM386 stealth,
+ and using LOADHI to see what address automatically became excluded
+ from the upper memory regions, and then attempting to load ARCETHER
+ using these addresses.
+
+ I recommend using an arcnet memory address of 0xD000, and putting
+ the EMS page frame at 0xC000 while using QEMM stealth mode. That
+ way, you get contiguous high memory from 0xD100 almost all the way
+ the end of the megabyte.
+
+ Memory Switch 0 (MS0) didn't seem to work properly when set to OFF
+ on my card. It could be malfunctioning on my card. Experiment with
+ it ON first, and if it doesn't work, set it to OFF. (It may be a
+ modifier for the 0x200 bit?)
+
+ MS Switch No.
+ 43210 Memory address
+ --------------------------------
+ 00001 0xE100 (guessed - was not detected by QEMM)
+ 00011 0xE000 (guessed - was not detected by QEMM)
+ 00101 0xDD00
+ 00111 0xDC00
+ 01001 0xD900
+ 01011 0xD800
+ 01101 0xD500
+ 01111 0xD400
+ 10001 0xD100
+ 10011 0xD000
+ 10101 0xCD00
+ 10111 0xCC00
+ 11001 0xC900 (guessed - crashes tested system)
+ 11011 0xC800 (guessed - crashes tested system)
+ 11101 0xC500 (guessed - crashes tested system)
+ 11111 0xC400 (guessed - crashes tested system)
+
+
+*****************************************************************************
+
+** CNet Technology Inc. **
+120 Series (8-bit cards)
+------------------------
+ - from Juergen Seifert <[email protected]>
+
+
+CNET TECHNOLOGY INC. (CNet) ARCNET 120A SERIES
+==============================================
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the following Original CNet Manual
+
+ "ARCNET
+ USER'S MANUAL
+ for
+ CN120A
+ CN120AB
+ CN120TP
+ CN120ST
+ CN120SBT
+ P/N:12-01-0007
+ Revision 3.00"
+
+ARCNET is a registered trademark of the Datapoint Corporation
+
+P/N 120A ARCNET 8 bit XT/AT Star
+P/N 120AB ARCNET 8 bit XT/AT Bus
+P/N 120TP ARCNET 8 bit XT/AT Twisted Pair
+P/N 120ST ARCNET 8 bit XT/AT Star, Twisted Pair
+P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair
+
+ __________________________________________________________________
+ | |
+ | ___|
+ | LED |___|
+ | ___|
+ | N | | ID7
+ | o | | ID6
+ | d | S | ID5
+ | e | W | ID4
+ | ___________________ A | 2 | ID3
+ | | | d | | ID2
+ | | | 1 2 3 4 5 6 7 8 d | | ID1
+ | | | _________________ r |___| ID0
+ | | 90C65 || SW1 | ____|
+ | JP 8 7 | ||_________________| | |
+ | |o|o| JP1 | | | J2 |
+ | |o|o| |oo| | | JP 1 1 1 | |
+ | ______________ | | 0 1 2 |____|
+ | | PROM | |___________________| |o|o|o| _____|
+ | > SOCKET | JP 6 5 4 3 2 |o|o|o| | J1 |
+ | |______________| |o|o|o|o|o| |o|o|o| |_____|
+ |_____ |o|o|o|o|o| ______________|
+ | |
+ |_____________________________________________|
+
+Legend:
+
+90C65 ARCNET Probe
+S1 1-5: Base Memory Address Select
+ 6-8: Base I/O Address Select
+S2 1-8: Node ID Select (ID0-ID7)
+JP1 ROM Enable Select
+JP2 IRQ2
+JP3 IRQ3
+JP4 IRQ4
+JP5 IRQ5
+JP6 IRQ7
+JP7/JP8 ET1, ET2 Timeout Parameters
+JP10/JP11 Coax / Twisted Pair Select (CN120ST/SBT only)
+JP12 Terminator Select (CN120AB/ST/SBT only)
+J1 BNC RG62/U Connector (all except CN120TP)
+J2 Two 6-position Telephone Jack (CN120TP/ST/SBT only)
+
+Setting one of the switches to Off means "1", On means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in SW2 are used to set the node ID. Each node attached
+to the network must have an unique node ID which must be diffrent from 0.
+Switch 1 (ID0) serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Label | Value
+ -------|-------|-------
+ 1 | ID0 | 1
+ 2 | ID1 | 2
+ 3 | ID2 | 4
+ 4 | ID3 | 8
+ 5 | ID4 | 16
+ 6 | ID5 | 32
+ 7 | ID6 | 64
+ 8 | ID7 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 8 7 6 5 4 3 2 1 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The last three switches in switch block SW1 are used to select one
+of eight possible I/O Base addresses using the followig table
+
+
+ Switch | Hex I/O
+ 6 7 8 | Address
+ ------------|--------
+ ON ON ON | 260
+ OFF ON ON | 290
+ ON OFF ON | 2E0 (Manufactor's default)
+ OFF OFF ON | 2F0
+ ON ON OFF | 300
+ OFF ON OFF | 350
+ ON OFF OFF | 380
+ OFF OFF OFF | 3E0
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The memory buffer (RAM) requires 2K. The base of this buffer can be
+located in any of eight positions. The address of the Boot Prom is
+memory base + 8K or memory base + 0x2000.
+Switches 1-5 of switch block SW1 select the Memory Base address.
+
+ Switch | Hex RAM | Hex ROM
+ 1 2 3 4 5 | Address | Address *)
+ --------------------|---------|-----------
+ ON ON ON ON ON | C0000 | C2000
+ ON ON OFF ON ON | C4000 | C6000
+ ON ON ON OFF ON | CC000 | CE000
+ ON ON OFF OFF ON | D0000 | D2000 (Manufactor's default)
+ ON ON ON ON OFF | D4000 | D6000
+ ON ON OFF ON OFF | D8000 | DA000
+ ON ON ON OFF OFF | DC000 | DE000
+ ON ON OFF OFF OFF | E0000 | E2000
+
+*) To enable the Boot ROM install the jumper JP1
+
+Note: Since the switches 1 and 2 are always set to ON it may be possible
+ that they can be used to add an offset of 2K, 4K or 6K to the base
+ address, but this feature is not documented in the manual and I
+ haven't testet it yet.
+
+
+Setting the Interrupt Line
+--------------------------
+
+To select a hardware interrupt level install one (only one!) of the jumpers
+JP2, JP3, JP4, JP5, JP6. JP2 is the default.
+
+ Jumper | IRQ
+ -------|-----
+ 2 | 2
+ 3 | 3
+ 4 | 4
+ 5 | 5
+ 6 | 7
+
+
+Setting the Internal Terminator on CN120AB/TP/SBT
+--------------------------------------------------
+
+The jumper JP12 is used to enable the internal terminator.
+
+ -----
+ 0 | 0 |
+ ----- ON | | ON
+ | 0 | | 0 |
+ | | OFF ----- OFF
+ | 0 | 0
+ -----
+ Terminator Terminator
+ disabled enabled
+
+
+Selecting the Connector Type on CN120ST/SBT
+-------------------------------------------
+
+ JP10 JP11 JP10 JP11
+ ----- -----
+ 0 0 | 0 | | 0 |
+ ----- ----- | | | |
+ | 0 | | 0 | | 0 | | 0 |
+ | | | | ----- -----
+ | 0 | | 0 | 0 0
+ ----- -----
+ Coaxial Cable Twisted Pair Cable
+ (Default)
+
+
+Setting the Timeout Parameters
+------------------------------
+
+The jumpers labeled EXT1 and EXT2 are used to determine the timeout
+parameters. These two jumpers are normally left open.
+
+
+
+*****************************************************************************
+
+** CNet Technology Inc. **
+160 Series (16-bit cards)
+-------------------------
+ - from Juergen Seifert <[email protected]>
+
+CNET TECHNOLOGY INC. (CNet) ARCNET 160A SERIES
+==============================================
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the following Original CNet Manual
+
+ "ARCNET
+ USER'S MANUAL
+ for
+ CN160A
+ CN160AB
+ CN160TP
+ P/N:12-01-0006
+ Revision 3.00"
+
+ARCNET is a registered trademark of the Datapoint Corporation
+
+P/N 160A ARCNET 16 bit XT/AT Star
+P/N 160AB ARCNET 16 bit XT/AT Bus
+P/N 160TP ARCNET 16 bit XT/AT Twisted Pair
+
+ ___________________________________________________________________
+ < _________________________ ___|
+ > |oo| JP2 | | LED |___|
+ < |oo| JP1 | 9026 | LED |___|
+ > |_________________________| ___|
+ < N | | ID7
+ > 1 o | | ID6
+ < 1 2 3 4 5 6 7 8 9 0 d | S | ID5
+ > _______________ _____________________ e | W | ID4
+ < | PROM | | SW1 | A | 2 | ID3
+ > > SOCKET | |_____________________| d | | ID2
+ < |_______________| | IO-Base | MEM | d | | ID1
+ > r |___| ID0
+ < ____|
+ > | |
+ < | J1 |
+ > | |
+ < |____|
+ > 1 1 1 1 |
+ < 3 4 5 6 7 JP 8 9 0 1 2 3 |
+ > |o|o|o|o|o| |o|o|o|o|o|o| |
+ < |o|o|o|o|o| __ |o|o|o|o|o|o| ___________|
+ > | | |
+ <____________| |_______________________________________|
+
+Legend:
+
+9026 ARCNET Probe
+SW1 1-6: Base I/O Address Select
+ 7-10: Base Memory Address Select
+SW2 1-8: Node ID Select (ID0-ID7)
+JP1/JP2 ET1, ET2 Timeout Parameters
+JP3-JP13 Interrupt Select
+J1 BNC RG62/U Connector (CN160A/AB only)
+J1 Two 6-position Telephone Jack (CN160TP only)
+LED
+
+Setting one of the switches to Off means "1", On means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in SW2 are used to set the node ID. Each node attached
+to the network must have an unique node ID which must be diffrent from 0.
+Switch 1 (ID0) serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Label | Value
+ -------|-------|-------
+ 1 | ID0 | 1
+ 2 | ID1 | 2
+ 3 | ID2 | 4
+ 4 | ID3 | 8
+ 5 | ID4 | 16
+ 6 | ID5 | 32
+ 7 | ID6 | 64
+ 8 | ID7 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 8 7 6 5 4 3 2 1 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The first six switches in switch block SW1 are used to select the I/O Base
+address using the followig table:
+
+ Switch | Hex I/O
+ 1 2 3 4 5 6 | Address
+ ------------------------|--------
+ OFF ON ON OFF OFF ON | 260
+ OFF ON OFF ON ON OFF | 290
+ OFF ON OFF OFF OFF ON | 2E0 (Manufactor's default)
+ OFF ON OFF OFF OFF OFF | 2F0
+ OFF OFF ON ON ON ON | 300
+ OFF OFF ON OFF ON OFF | 350
+ OFF OFF OFF ON ON ON | 380
+ OFF OFF OFF OFF OFF ON | 3E0
+
+Note: Other IO-Base addresses seem to be selectable, but only the above
+ combinations are documented.
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The switches 7-10 of switch block SW1 are used to select the Memory
+Base address of the RAM (2K) and the PROM.
+
+ Switch | Hex RAM | Hex ROM
+ 7 8 9 10 | Address | Address
+ ----------------|---------|-----------
+ OFF OFF ON ON | C0000 | C8000
+ OFF OFF ON OFF | D0000 | D8000 (Default)
+ OFF OFF OFF ON | E0000 | E8000
+
+Note: Other MEM-Base addresses seem to be selectable, but only the above
+ combinations are documented.
+
+
+Setting the Interrupt Line
+--------------------------
+
+To select a hardware interrupt level install one (only one!) of the jumpers
+JP3 through JP13 using the following table:
+
+ Jumper | IRQ
+ -------|-----------------
+ 3 | 14
+ 4 | 15
+ 5 | 12
+ 6 | 11
+ 7 | 10
+ 8 | 3
+ 9 | 4
+ 10 | 5
+ 11 | 6
+ 12 | 7
+ 13 | 2 (=9) Default!
+
+Note: - Do not use JP11=IRQ6, it may conflict with your Floppy Disk
+ Controler
+ - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL-
+ Hard Disk, it may conflict with their controlers
+
+
+Setting the Timeout Parameters
+------------------------------
+
+The jumpers labeled JP1 and JP2 are used to determine the timeout
+parameters. These two jumpers are normally left open.
+
+
+*****************************************************************************
+
+** No Name **
+8-bit cards, 16-bit cards
+-------------------------
+ - from Juergen Seifert <[email protected]>
+
+NONAME 8-BIT ARCNET
+===================
+
+I have named this ARCnet card "NONAME", since there is no name of any
+manufactor on the Installation manual nor on the shipping box. The only
+hint to the existence of a manufactor at all is written into cupper,
+it is "Made in Taiwan"
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the Original
+ "ARCnet Installation Manual"
+
+
+ ________________________________________________________________
+ | |STAR| BUS| T/P| |
+ | |____|____|____| |
+ | _____________________ |
+ | | | |
+ | | | |
+ | | | |
+ | | SMC | |
+ | | | |
+ | | COM90C65 | |
+ | | | |
+ | | | |
+ | |__________-__________| |
+ | _____|
+ | _______________ | CN |
+ | | PROM | |_____|
+ | > SOCKET | |
+ | |_______________| 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 |
+ | _______________ _______________ |
+ | |o|o|o|o|o|o|o|o| | SW1 || SW2 ||
+ | |o|o|o|o|o|o|o|o| |_______________||_______________||
+ |___ 2 3 4 5 7 E E R Node ID IOB__|__MEM____|
+ | \ IRQ / T T O |
+ |__________________1_2_M______________________|
+
+Legend:
+
+COM90C65: Arcnet Probe
+S1 1-8: Node ID Select
+S2 1-3: I/O Base Address Select
+ 4-6: Memory Base Address Select
+ 7-8: RAM Offset Select
+ET1, ET2 Extended Timeout Select
+ROM ROM Enable Select
+CN RG62 Coax Connector
+STAR| BUS | T/P Three fields for placing a sign (colored circle)
+ indicating the topologie of the card
+
+Setting one of the switches to Off means "1", On means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in group SW1 are used to set the node ID.
+Each node attached to the network must have an unique node ID which
+must be diffrent from 0.
+Switch 8 serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Value
+ -------|-------
+ 8 | 1
+ 7 | 2
+ 6 | 4
+ 5 | 8
+ 4 | 16
+ 3 | 32
+ 2 | 64
+ 1 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 1 2 3 4 5 6 7 8 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The first three switches in switch group SW2 are used to select one
+of eight possible I/O Base addresses using the followig table
+
+ Switch | Hex I/O
+ 1 2 3 | Address
+ ------------|--------
+ ON ON ON | 260
+ ON ON OFF | 290
+ ON OFF ON | 2E0 (Manufactor's default)
+ ON OFF OFF | 2F0
+ OFF ON ON | 300
+ OFF ON OFF | 350
+ OFF OFF ON | 380
+ OFF OFF OFF | 3E0
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The memory buffer requires 2K of a 16K block of RAM. The base of this
+16K block can be located in any of eight positions.
+Switches 4-6 of switch group SW2 select the Base of the 16K block.
+Within that 16K address space, the buffer may be assigned any one of four
+positions, determined by the offset, switches 7 and 8 of group SW2.
+
+ Switch | Hex RAM | Hex ROM
+ 4 5 6 7 8 | Address | Address *)
+ -----------|---------|-----------
+ 0 0 0 0 0 | C0000 | C2000
+ 0 0 0 0 1 | C0800 | C2000
+ 0 0 0 1 0 | C1000 | C2000
+ 0 0 0 1 1 | C1800 | C2000
+ | |
+ 0 0 1 0 0 | C4000 | C6000
+ 0 0 1 0 1 | C4800 | C6000
+ 0 0 1 1 0 | C5000 | C6000
+ 0 0 1 1 1 | C5800 | C6000
+ | |
+ 0 1 0 0 0 | CC000 | CE000
+ 0 1 0 0 1 | CC800 | CE000
+ 0 1 0 1 0 | CD000 | CE000
+ 0 1 0 1 1 | CD800 | CE000
+ | |
+ 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
+ 0 1 1 0 1 | D0800 | D2000
+ 0 1 1 1 0 | D1000 | D2000
+ 0 1 1 1 1 | D1800 | D2000
+ | |
+ 1 0 0 0 0 | D4000 | D6000
+ 1 0 0 0 1 | D4800 | D6000
+ 1 0 0 1 0 | D5000 | D6000
+ 1 0 0 1 1 | D5800 | D6000
+ | |
+ 1 0 1 0 0 | D8000 | DA000
+ 1 0 1 0 1 | D8800 | DA000
+ 1 0 1 1 0 | D9000 | DA000
+ 1 0 1 1 1 | D9800 | DA000
+ | |
+ 1 1 0 0 0 | DC000 | DE000
+ 1 1 0 0 1 | DC800 | DE000
+ 1 1 0 1 0 | DD000 | DE000
+ 1 1 0 1 1 | DD800 | DE000
+ | |
+ 1 1 1 0 0 | E0000 | E2000
+ 1 1 1 0 1 | E0800 | E2000
+ 1 1 1 1 0 | E1000 | E2000
+ 1 1 1 1 1 | E1800 | E2000
+
+*) To enable the 8K Boot PROM install the jumper ROM.
+ The default is jumper ROM not installed.
+
+
+Setting Interrupt Request Lines (IRQ)
+-------------------------------------
+
+To select a hardware interrupt level set one (only one!) of the jumpers
+IRQ2, IRQ3, IRQ4, IRQ5 or IRQ7. The Manufactor's default is IRQ2.
+
+
+Setting the Timeouts
+--------------------
+
+The two jumpers labeled ET1 and ET2 are used to determine the timeout
+parameters (respons and reconfiguration time). Every node in a network
+must be set to the same timeout values.
+
+ ET1 ET2 | Response Time (us) | Reconfiguration Time (ms)
+ --------|--------------------|--------------------------
+ Off Off | 78 | 840 (Default)
+ Off On | 285 | 1680
+ On Off | 563 | 1680
+ On On | 1130 | 1680
+
+On means jumper installed, Off means jumper not installed
+
+
+NONAME 16-BIT ARCNET
+====================
+
+The manual of my 8-Bit NONAME ARCnet Card contains another description
+of a 16-Bit Coax / Twisted Pair Card. This description is incomplete,
+because there are missing two pages in the manual booklet. (The table
+of contents reports pages ... 2-9, 2-11, 2-12, 3-1, ... but inside
+the booklet there is a diffrent way of counting ... 2-9, 2-10, A-1,
+(empty page), 3-1, ..., 3-18, A-1 (again), A-2)
+Also the picture of the board layout is not as good as the picture of
+8-Bit card, because there isn't any letter like "SW1" written to the
+picture.
+Should somebody have such a board, please feel free to complete this
+description or to send a mail to me!
+
+This description has been written by Juergen Seifert <[email protected]>
+using information from the Original
+ "ARCnet Installation Manual"
+
+
+ ___________________________________________________________________
+ < _________________ _________________ |
+ > | SW? || SW? | |
+ < |_________________||_________________| |
+ > ____________________ |
+ < | | |
+ > | | |
+ < | | |
+ > | | |
+ < | | |
+ > | | |
+ < | | |
+ > |____________________| |
+ < ____|
+ > ____________________ | |
+ < | | | J1 |
+ > | < | |
+ < |____________________| ? ? ? ? ? ? |____|
+ > |o|o|o|o|o|o| |
+ < |o|o|o|o|o|o| |
+ > |
+ < __ ___________|
+ > | | |
+ <____________| |_______________________________________|
+
+
+Setting one of the switches to Off means "1", On means "0".
+
+
+Setting the Node ID
+-------------------
+
+The eight switches in group SW2 are used to set the node ID.
+Each node attached to the network must have an unique node ID which
+must be diffrent from 0.
+Switch 8 serves as the least significant bit (LSB).
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Value
+ -------|-------
+ 8 | 1
+ 7 | 2
+ 6 | 4
+ 5 | 8
+ 4 | 16
+ 3 | 32
+ 2 | 64
+ 1 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 1 2 3 4 5 6 7 8 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The first three switches in switch group SW1 are used to select one
+of eight possible I/O Base addresses using the followig table
+
+ Switch | Hex I/O
+ 3 2 1 | Address
+ ------------|--------
+ ON ON ON | 260
+ ON ON OFF | 290
+ ON OFF ON | 2E0 (Manufactor's default)
+ ON OFF OFF | 2F0
+ OFF ON ON | 300
+ OFF ON OFF | 350
+ OFF OFF ON | 380
+ OFF OFF OFF | 3E0
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The memory buffer requires 2K of a 16K block of RAM. The base of this
+16K block can be located in any of eight positions.
+Switches 6-8 of switch group SW1 select the Base of the 16K block.
+Within that 16K address space, the buffer may be assigned any one of four
+positions, determined by the offset, switches 4 and 5 of group SW1.
+
+ Switch | Hex RAM | Hex ROM
+ 8 7 6 5 4 | Address | Address
+ -----------|---------|-----------
+ 0 0 0 0 0 | C0000 | C2000
+ 0 0 0 0 1 | C0800 | C2000
+ 0 0 0 1 0 | C1000 | C2000
+ 0 0 0 1 1 | C1800 | C2000
+ | |
+ 0 0 1 0 0 | C4000 | C6000
+ 0 0 1 0 1 | C4800 | C6000
+ 0 0 1 1 0 | C5000 | C6000
+ 0 0 1 1 1 | C5800 | C6000
+ | |
+ 0 1 0 0 0 | CC000 | CE000
+ 0 1 0 0 1 | CC800 | CE000
+ 0 1 0 1 0 | CD000 | CE000
+ 0 1 0 1 1 | CD800 | CE000
+ | |
+ 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
+ 0 1 1 0 1 | D0800 | D2000
+ 0 1 1 1 0 | D1000 | D2000
+ 0 1 1 1 1 | D1800 | D2000
+ | |
+ 1 0 0 0 0 | D4000 | D6000
+ 1 0 0 0 1 | D4800 | D6000
+ 1 0 0 1 0 | D5000 | D6000
+ 1 0 0 1 1 | D5800 | D6000
+ | |
+ 1 0 1 0 0 | D8000 | DA000
+ 1 0 1 0 1 | D8800 | DA000
+ 1 0 1 1 0 | D9000 | DA000
+ 1 0 1 1 1 | D9800 | DA000
+ | |
+ 1 1 0 0 0 | DC000 | DE000
+ 1 1 0 0 1 | DC800 | DE000
+ 1 1 0 1 0 | DD000 | DE000
+ 1 1 0 1 1 | DD800 | DE000
+ | |
+ 1 1 1 0 0 | E0000 | E2000
+ 1 1 1 0 1 | E0800 | E2000
+ 1 1 1 1 0 | E1000 | E2000
+ 1 1 1 1 1 | E1800 | E2000
+
+
+Setting Interrupt Request Lines (IRQ)
+-------------------------------------
+
+??????????????????????????????????????
+
+
+Setting the Timeouts
+--------------------
+
+??????????????????????????????????????
+
+
+*****************************************************************************
+
+** No Name **
+8-bit cards ("Made in Taiwan R.O.C.")
+-----------
+ - from Vojtech Pavlik <[email protected]>
+
+I have named this ARCnet card "NONAME", since I got only the card with
+no manual at all and the only text identifying the manufacturer is
+"MADE IN TAIWAN R.O.C" printed on the card.
+
+This description was written by Vojtech Pavlik
+([email protected]) using parts of the ARCNET-jumpers
+README file from Linux kernel 1.2.2.
+
+ ____________________________________________________________
+ | 1 2 3 4 5 6 7 8 |
+ | |o|o| JP1 o|o|o|o|o|o|o|o| ON |
+ | + o|o|o|o|o|o|o|o| ___|
+ | _____________ o|o|o|o|o|o|o|o| OFF _____ | | ID7
+ | | | SW1 | | | | ID6
+ | > RAM (2k) | ____________________ | H | | S | ID5
+ | |_____________| | || y | | W | ID4
+ | | || b | | 2 | ID3
+ | | || r | | | ID2
+ | | || i | | | ID1
+ | | 90C65 || d | |___| ID0
+ | SW3 | || | |
+ | |o|o|o|o|o|o|o|o| ON | || I | |
+ | |o|o|o|o|o|o|o|o| | || C | |
+ | |o|o|o|o|o|o|o|o| OFF |____________________|| | _____|
+ | 1 2 3 4 5 6 7 8 | | | |___
+ | ______________ | | | BNC |___|
+ | | | |_____| |_____|
+ | > EPROM SOCKET | |
+ | |______________| |
+ | ______________|
+ | |
+ |_____________________________________________|
+
+Legend:
+
+90C65 ARCNET Chip
+SW1 1-5: Base Memory Address Select
+ 6-8: Base I/O Address Select
+SW2 1-8: Node ID Select (ID0-ID7)
+SW3 1-5: IRQ Select
+ 6-7: Extra Timeout
+ 8 : Rom Enable
+JP1 Led connector
+BNC Coax connector
+
+Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
+switches.
+
+Setting the jumpers to ON means connecting the upper two pins, off the bottom
+two - or - in case of IRQ setting, connecting none of them at all.
+
+Setting the Node ID
+-------------------
+
+The eight switches in SW2 are used to set the node ID. Each node attached
+to the network must have an unique node ID which must be diffrent from 0.
+Switch 1 (ID0) serves as the least significant bit (LSB).
+
+Setting one of the switches to Off means "1", On means "0".
+
+The node ID is the sum of the values of all switches set to "1"
+These values are:
+
+ Switch | Label | Value
+ -------|-------|-------
+ 1 | ID0 | 1
+ 2 | ID1 | 2
+ 3 | ID2 | 4
+ 4 | ID3 | 8
+ 5 | ID4 | 16
+ 6 | ID5 | 32
+ 7 | ID6 | 64
+ 8 | ID7 | 128
+
+Some Examples:
+
+ Switch | Hex | Decimal
+ 8 7 6 5 4 3 2 1 | Node ID | Node ID
+ ----------------|---------|---------
+ 0 0 0 0 0 0 0 0 | not allowed
+ 0 0 0 0 0 0 0 1 | 1 | 1
+ 0 0 0 0 0 0 1 0 | 2 | 2
+ 0 0 0 0 0 0 1 1 | 3 | 3
+ . . . | |
+ 0 1 0 1 0 1 0 1 | 55 | 85
+ . . . | |
+ 1 0 1 0 1 0 1 0 | AA | 170
+ . . . | |
+ 1 1 1 1 1 1 0 1 | FD | 253
+ 1 1 1 1 1 1 1 0 | FE | 254
+ 1 1 1 1 1 1 1 1 | FF | 255
+
+
+Setting the I/O Base Address
+----------------------------
+
+The last three switches in switch block SW1 are used to select one
+of eight possible I/O Base addresses using the followig table
+
+
+ Switch | Hex I/O
+ 6 7 8 | Address
+ ------------|--------
+ ON ON ON | 260
+ OFF ON ON | 290
+ ON OFF ON | 2E0 (Manufactor's default)
+ OFF OFF ON | 2F0
+ ON ON OFF | 300
+ OFF ON OFF | 350
+ ON OFF OFF | 380
+ OFF OFF OFF | 3E0
+
+
+Setting the Base Memory (RAM) buffer Address
+--------------------------------------------
+
+The memory buffer (RAM) requires 2K. The base of this buffer can be
+located in any of eight positions. The address of the Boot Prom is
+memory base + 0x2000.
+Jumpers 3-5 of jumper block SW1 select the Memory Base address.
+
+ Switch | Hex RAM | Hex ROM
+ 1 2 3 4 5 | Address | Address *)
+ --------------------|---------|-----------
+ ON ON ON ON ON | C0000 | C2000
+ ON ON OFF ON ON | C4000 | C6000
+ ON ON ON OFF ON | CC000 | CE000
+ ON ON OFF OFF ON | D0000 | D2000 (Manufactor's default)
+ ON ON ON ON OFF | D4000 | D6000
+ ON ON OFF ON OFF | D8000 | DA000
+ ON ON ON OFF OFF | DC000 | DE000
+ ON ON OFF OFF OFF | E0000 | E2000
+
+*) To enable the Boot ROM set the jumper 8 of jumper block SW3 to position ON.
+
+The jumpers 1 and 2 probably add 0x0800, 0x1000 and 0x1800 to RAM addres.
+
+Setting the Interrupt Line
+--------------------------
+
+Jumpers 1-5 of the jumper block SW3 controll the IRQ level.
+
+ Jumper | IRQ
+ 1 2 3 4 5 |
+ ----------------------------
+ ON OFF OFF OFF OFF | 2
+ OFF ON OFF OFF OFF | 3
+ OFF OFF ON OFF OFF | 4
+ OFF OFF OFF ON OFF | 5
+ OFF OFF OFF OFF ON | 7
+
+
+Setting the Timeout Parameters
+------------------------------
+
+The jumpers 6-7 of the jumper block SW3 are used to determine the timeout
+parameters. These two jumpers are normally left in the OFF position.
+
+
+*****************************************************************************
+** Tiara **
+(model unknown)
+-------------------------
+ - from Christoph Lameter <[email protected]>
+
+
+Here is information about my card as far as I could figure it out:
+----------------------------------------------- tiara
+Tiara LanCard of Tiara Computer Systems.
+
++----------------------------------------------+
+! ! Transmitter Unit ! !
+! +------------------+ -------
+! MEM Coax Connector
+! ROM 7654321 <- I/O -------
+! : : +--------+ !
+! : : ! 90C66LJ! +++
+! : : ! ! !D Switch to set
+! : : ! ! !I the Nodenumber
+! : : +--------+ !P
+! !++
+! 234567 <- IRQ !
++------------!!!!!!!!!!!!!!!!!!!!!!!!--------+
+ !!!!!!!!!!!!!!!!!!!!!!!!
+
+0 = Jumper Installed
+1 = Open
+
+Top Jumper line Bit 7 = Rom Enable 654=Memory location 321=I/O
+
+Settings for Memory Location (Top Jumper Line)
+456 Address selected
+000 C0000
+001 C4000
+010 CC000
+011 D0000
+100 D4000
+101 D8000
+110 DC000
+111 E0000
+
+Settings for I/O Address (Top Jumper Line)
+123 Port
+000 260
+001 290
+010 2E0
+011 2F0
+100 300
+101 350
+110 380
+111 3E0
+
+Settings for IRQ Selection (Lower Jumper Line)
+234567
+011111 IRQ 2
+101111 IRQ 3
+110111 IRQ 4
+111011 IRQ 5
+111110 IRQ 7
+
+*****************************************************************************
+
+
+Other Cards
+-----------
+
+I have no information on other models of ARCnet cards at the moment. Please
+send any and all info to:
+ [email protected]
+
+Thanks.
FUNET's LINUX-ADM group, [email protected]
TCL-scripts by Sam Shen, [email protected]
with Sam's (original) version of this