patch-1.3.22 linux/drivers/char/serial.c
Next file: linux/drivers/char/tpqic02.c
Previous file: linux/drivers/char/scc_config.h
Back to the patch index
Back to the overall index
- Lines: 83
- Date:
Tue Aug 29 10:15:51 1995
- Orig file:
v1.3.21/linux/drivers/char/serial.c
- Orig date:
Mon Aug 28 14:52:20 1995
diff -u --recursive --new-file v1.3.21/linux/drivers/char/serial.c linux/drivers/char/serial.c
@@ -71,7 +71,7 @@
#undef SERIAL_DEBUG_OPEN
#undef SERIAL_DEBUG_FLOW
-#define RS_STROBE_TIME 10
+#define RS_STROBE_TIME (10*HZ)
#define RS_ISR_PASS_LIMIT 256
#define _INLINE_ inline
@@ -765,7 +765,7 @@
struct async_struct *info;
unsigned int i;
- if ((jiffies - last_strobe) >= RS_STROBE_TIME*HZ) {
+ if ((jiffies - last_strobe) >= RS_STROBE_TIME) {
for (i=1; i < 16; i++) {
info = IRQ_ports[i];
if (!info)
@@ -788,7 +788,7 @@
}
}
last_strobe = jiffies;
- timer_table[RS_TIMER].expires = jiffies + RS_STROBE_TIME * HZ;
+ timer_table[RS_TIMER].expires = jiffies + RS_STROBE_TIME;
timer_active |= 1 << RS_TIMER;
if (IRQ_ports[0]) {
@@ -1016,7 +1016,7 @@
/*
* Set up serial timers...
*/
- timer_table[RS_TIMER].expires = jiffies + 2;
+ timer_table[RS_TIMER].expires = jiffies + 2*HZ/100;
timer_active |= 1 << RS_TIMER;
/*
@@ -1519,8 +1519,8 @@
(new_serial.flags & ASYNC_FLAGS));
info->custom_divisor = new_serial.custom_divisor;
info->type = new_serial.type;
- info->close_delay = new_serial.close_delay;
- info->closing_wait = new_serial.closing_wait;
+ info->close_delay = new_serial.close_delay * HZ/100;
+ info->closing_wait = new_serial.closing_wait * HZ/100;
release_region(info->port,8);
if (change_port || change_irq) {
@@ -1703,13 +1703,13 @@
* Delay for 0.1 seconds -- we use a busy loop since this may
* occur during the bootup sequence
*/
- timeout = jiffies+10;
+ timeout = jiffies+HZ/10;
while (timeout >= jiffies)
;
rs_triggered = 0; /* Reset after letting things settle */
- timeout = jiffies+10;
+ timeout = jiffies+HZ/10;
while (timeout >= jiffies)
;
@@ -2386,7 +2386,7 @@
(void)serial_inp(info, UART_IIR);
(void)serial_inp(info, UART_MSR);
- timeout = jiffies+2;
+ timeout = jiffies+2*HZ/100;
while (timeout >= jiffies) {
if (rs_irq_triggered)
break;
@@ -2648,8 +2648,8 @@
info->tty = 0;
info->type = PORT_UNKNOWN;
info->custom_divisor = 0;
- info->close_delay = 50;
- info->closing_wait = 3000;
+ info->close_delay = 5*HZ/10;
+ info->closing_wait = 30*HZ;
info->x_char = 0;
info->event = 0;
info->count = 0;
FUNET's LINUX-ADM group, [email protected]
TCL-scripts by Sam Shen, [email protected]
with Sam's (original) version of this