patch-1.3.27 linux/include/linux/cdk.h

• Lines: 473
• Date: Thu Sep 14 15:03:37 1995
• Orig file: v1.3.26/linux/include/linux/cdk.h
• Orig date: Thu Jan 1 02:00:00 1970

diff -u --recursive --new-file v1.3.26/linux/include/linux/cdk.h linux/include/linux/cdk.h
@@ -0,0 +1,472 @@
+/*****************************************************************************/
+
+/*
+ *	cdk.h  -- CDK interface definitions.
+ *
+ *	Copyright (C) 1994,1995  Greg Ungerer ([email protected]).
+ *
+ *	This program is free software; you can redistribute it and/or modify
+ *	it under the terms of the GNU General Public License as published by
+ *	the Free Software Foundation; either version 2 of the License, or
+ *	(at your option) any later version.
+ *
+ *	This program is distributed in the hope that it will be useful,
+ *	but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *	GNU General Public License for more details.
+ *
+ *	You should have received a copy of the GNU General Public License
+ *	along with this program; if not, write to the Free Software
+ *	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*****************************************************************************/
+
+#ifndef	_CDK_H
+#define	_CDK_H
+/*****************************************************************************/
+
+#pragma	pack(2)
+
+/*
+ *	The following set of definitions is used to communicate with the
+ *	shared memory interface of the Stallion intelligent multiport serial
+ *	boards. The definitions in this file are taken directly from the
+ *	document titled "Generic Stackable Interface, Downloader and
+ *	Communications Development Kit".
+ */
+
+/*
+ *	Define the set of importrant shared memory addresses. These are
+ *	required to intialize the board and get things started. All of these
+ *	addresses are relative to the start of the shared memory.
+ */
+#define	CDK_SIGADDR	0x200
+#define	CDK_FEATADDR	0x280
+#define	CDK_CDKADDR	0x300
+#define	CDK_RDYADDR	0x262
+
+#define	CDK_ALIVEMARKER	13
+
+/*
+ *	On hardware power up the ROMs located on the EasyConnection 8/64 will
+ *	fill out the following signature information into shared memory. This
+ *	way the host system can quickly determine that the board is present
+ *	and is operational.
+ */
+typedef struct cdkecpsig {
+	unsigned long	magic;
+	unsigned short	romver;
+	unsigned short	cputype;
+	unsigned char	panelid[8];
+} cdkecpsig_t;
+
+#define	ECP_MAGIC	0x21504345
+
+/*
+ *	On hardware power up the ROMs located on the ONboard, Stallion and
+ *	Brumbys will fill out the following signature information into shared
+ *	memory. This way the host system can quickly determine that the board
+ *	is present and is operational.
+ */
+typedef struct cdkonbsig {
+	unsigned short	magic0;
+	unsigned short	magic1;
+	unsigned short	magic2;
+	unsigned short	magic3;
+	unsigned short	romver;
+	unsigned short	memoff;
+	unsigned short	memseg;
+	unsigned short	amask0;
+	unsigned short	pic;
+	unsigned short	status;
+	unsigned short	btype;
+	unsigned short	clkticks;
+	unsigned short	clkspeed;
+	unsigned short	amask1;
+	unsigned short	amask2;
+} cdkonbsig_t;
+
+#define	ONB_MAGIC0	0xf2a7
+#define	ONB_MAGIC1	0xa149
+#define	ONB_MAGIC2	0x6352
+#define	ONB_MAGIC3	0xf121
+
+/*
+ *	Define the feature area structure. The feature area is the set of
+ *	startup parameters used by the slave image when it starts executing.
+ *	They allow for the specification of buffer sizes, debug trace, etc.
+ */
+typedef struct cdkfeature {
+	unsigned long	debug;
+	unsigned long	banner;
+	unsigned long	etype;
+	unsigned long	nrdevs;
+	unsigned long	brdspec;
+	unsigned long	txrqsize;
+	unsigned long	rxrqsize;
+	unsigned long	flags;
+} cdkfeature_t;
+
+#define	ETYP_DDK	0
+#define	ETYP_CDK	1
+
+/*
+ *	Define the CDK header structure. This is the info that the slave
+ *	environment sets up after it has been downloaded and started. It
+ *	essentially provides a memory map for the shared memory interface.
+ */
+typedef struct cdkhdr {
+	unsigned short	command;
+	unsigned short	status;
+	unsigned short	port;
+	unsigned short	mode;
+	unsigned long	cmd_buf[14];
+	unsigned short	alive_cnt;
+	unsigned short	intrpt_mode;
+	unsigned char	intrpt_id[8];
+	unsigned char	ver_release;
+	unsigned char	ver_modification;
+	unsigned char	ver_fix;
+	unsigned char	deadman_restart;
+	unsigned short	deadman;
+	unsigned short	nrdevs;
+	unsigned long	memp;
+	unsigned long	hostp;
+	unsigned long	slavep;
+	unsigned char	hostreq;
+	unsigned char	slavereq;
+	unsigned char	cmd_reserved[30];
+} cdkhdr_t;
+
+#define	MODE_DDK	0
+#define	MODE_CDK	1
+
+#define	IMD_INTR	0x0
+#define	IMD_PPINTR	0x1
+#define	IMD_POLL	0xff
+
+/*
+ *	Define the memory mapping structure. This structure is pointed to by
+ *	the memp field in the stlcdkhdr struct. As many as these structures
+ *	as required are layed out in shared memory to define how the rest of
+ *	shared memory is divided up. There will be one for each port.
+ */
+typedef struct cdkmem {
+	unsigned short	dtype;
+	unsigned long	offset;
+} cdkmem_t;
+
+#define	TYP_UNDEFINED	0x0
+#define	TYP_ASYNCTRL	0x1
+#define	TYP_ASYNC	0x20
+#define	TYP_PARALLEL	0x40
+#define	TYP_SYNCX21	0x60
+
+/*****************************************************************************/
+
+/*
+ *	Following is a set of defines and structures used to actually deal
+ *	with the serial ports on the board. Firstly is the set of commands
+ *	that can be applied to ports.
+ */
+#define	ASYCMD		(((unsigned long) 'a') << 8)
+
+#define	A_NULL		(ASYCMD | 0)
+#define	A_FLUSH		(ASYCMD | 1)
+#define	A_BREAK		(ASYCMD | 2)
+#define	A_GETPORT	(ASYCMD | 3)
+#define	A_SETPORT	(ASYCMD | 4)
+#define	A_SETPORTF	(ASYCMD | 5)
+#define	A_SETPORTFTX	(ASYCMD | 6)
+#define	A_SETPORTFRX	(ASYCMD | 7)
+#define	A_GETSIGNALS	(ASYCMD | 8)
+#define	A_SETSIGNALS	(ASYCMD | 9)
+#define	A_SETSIGNALSF	(ASYCMD | 10)
+#define	A_SETSIGNALSFTX	(ASYCMD | 11)
+#define	A_SETSIGNALSFRX	(ASYCMD | 12)
+#define	A_GETNOTIFY	(ASYCMD | 13)
+#define	A_SETNOTIFY	(ASYCMD | 14)
+#define	A_NOTIFY	(ASYCMD | 15)
+#define	A_PORTCTRL	(ASYCMD | 16)
+#define	A_GETSTATS	(ASYCMD | 17)
+#define	A_RQSTATE	(ASYCMD | 18)
+#define	A_FLOWSTATE	(ASYCMD | 19)
+
+/*
+ *	Define those arguments used for simple commands.
+ */
+#define	FLUSHRX		0x1
+#define	FLUSHTX		0x2
+
+#define	BREAKON		-1
+#define	BREAKOFF	-2
+
+/*
+ *	Define the port setting structure, and all those defines that go along
+ *	with it. Basically this structure defines the charcateristics of this
+ *	port: baud rate, chars, parity, input/output char cooking etc.
+ */
+typedef struct asyport {
+	unsigned long	baudout;
+	unsigned long	baudin;
+	unsigned long	iflag;
+	unsigned long	oflag;
+	unsigned long	lflag;
+	unsigned long	pflag;
+	unsigned long	flow;
+	unsigned long	spare1;
+	unsigned short	vtime;
+	unsigned short	vmin;
+	unsigned short	txlo;
+	unsigned short	txhi;
+	unsigned short	rxlo;
+	unsigned short	rxhi;
+	unsigned short	rxhog;
+	unsigned short	spare2;
+	unsigned char	csize;
+	unsigned char	stopbs;
+	unsigned char	parity;
+	unsigned char	stopin;
+	unsigned char	startin;
+	unsigned char	stopout;
+	unsigned char	startout;
+	unsigned char	parmark;
+	unsigned char	brkmark;
+	unsigned char	cc[11];
+} asyport_t;
+
+#define	PT_STOP1	0x0
+#define	PT_STOP15	0x1
+#define	PT_STOP2	0x2
+
+#define	PT_NOPARITY	0x0
+#define	PT_ODDPARITY	0x1
+#define	PT_EVENPARITY	0x2
+#define	PT_MARKPARITY	0x3
+#define	PT_SPACEPARITY	0x4
+
+#define	F_NONE		0x0
+#define	F_IXON		0x1
+#define	F_IXOFF		0x2
+#define	F_IXANY		0x4
+#define	F_IOXANY	0x8
+#define	F_RTSFLOW	0x10
+#define	F_CTSFLOW	0x20
+#define	F_DTRFLOW	0x40
+#define	F_DCDFLOW	0x80
+#define	F_DSROFLOW	0x100
+#define	F_DSRIFLOW	0x200
+
+#define	FI_NORX		0x1
+#define	FI_RAW		0x2
+#define	FI_ISTRIP	0x4
+#define	FI_UCLC		0x8
+#define	FI_INLCR	0x10
+#define	FI_ICRNL	0x20
+#define	FI_IGNCR	0x40
+#define	FI_IGNBREAK	0x80
+#define	FI_DSCRDBREAK	0x100
+#define	FI_1MARKBREAK	0x200
+#define	FI_2MARKBREAK	0x400
+#define	FI_XCHNGBREAK	0x800
+#define	FI_IGNRXERRS	0x1000
+#define	FI_DSCDRXERRS	0x2000
+#define	FI_1MARKRXERRS	0x4000
+#define	FI_2MARKRXERRS	0x8000
+#define	FI_XCHNGRXERRS	0x10000
+#define	FI_DSCRDNULL	0x20000
+
+#define	FO_OLCUC	0x1
+#define	FO_ONLCR	0x2
+#define	FO_OOCRNL	0x4
+#define	FO_ONOCR	0x8
+#define	FO_ONLRET	0x10
+#define	FO_ONL		0x20
+#define	FO_OBS		0x40
+#define	FO_OVT		0x80
+#define	FO_OFF		0x100
+#define	FO_OTAB1	0x200
+#define	FO_OTAB2	0x400
+#define	FO_OTAB3	0x800
+#define	FO_OCR1		0x1000
+#define	FO_OCR2		0x2000
+#define	FO_OCR3		0x4000
+#define	FO_OFILL	0x8000
+#define	FO_ODELL	0x10000
+
+#define	P_RTSLOCK	0x1
+#define	P_CTSLOCK	0x2
+#define	P_MAPRTS	0x4
+#define	P_MAPCTS	0x8
+#define	P_LOOPBACK	0x10
+#define	P_DTRFOLLOW	0x20
+#define	P_FAKEDCD	0x40
+
+/*
+ *	Define a structure to communicate serial port signal and data state
+ *	information.
+ */
+typedef struct asysigs {
+	unsigned long	data;
+	unsigned long	signal;
+	unsigned long	sigvalue;
+} asysigs_t;
+
+#define	DT_TXBUSY	0x1
+#define	DT_TXEMPTY	0x2
+#define	DT_TXLOW	0x4
+#define	DT_TXHIGH	0x8
+#define	DT_TXFULL	0x10
+#define	DT_TXHOG	0x20
+#define	DT_TXFLOWED	0x40
+#define	DT_TXBREAK	0x80
+
+#define	DT_RXBUSY	0x100
+#define	DT_RXEMPTY	0x200
+#define	DT_RXLOW	0x400
+#define	DT_RXHIGH	0x800
+#define	DT_RXFULL	0x1000
+#define	DT_RXHOG	0x2000
+#define	DT_RXFLOWED	0x4000
+#define	DT_RXBREAK	0x8000
+
+#define	SG_DTR		0x1
+#define	SG_DCD		0x2
+#define	SG_RTS		0x4
+#define	SG_CTS		0x8
+#define	SG_DSR		0x10
+#define	SG_RI		0x20
+
+/*
+ *	Define the notification setting structure. This is used to tell the
+ *	port what events we want to be informed about. Fields here use the
+ *	same defines as for the asysigs structure above.
+ */
+typedef struct asynotify {
+	unsigned long	ctrl;
+	unsigned long	data;
+	unsigned long	signal;
+	unsigned long	sigvalue;
+} asynotify_t;
+
+/*
+ *	Define the port control structure. It is used to do fine grain
+ *	control operations on the port.
+ */
+typedef struct {
+	unsigned long	rxctrl;
+	unsigned long	txctrl;
+	char		rximdch;
+	char		tximdch;
+	char		spare1;
+	char		spare2;
+} asyctrl_t;
+
+#define	CT_ENABLE	0x1
+#define	CT_DISABLE	0x2
+#define	CT_STOP		0x4
+#define	CT_START	0x8
+#define	CT_STARTFLOW	0x10
+#define	CT_STOPFLOW	0x20
+#define	CT_SENDCHR	0x40
+
+/*
+ *	Define the stats structure kept for each port. This is a useful set
+ *	of data collected for each port on the slave. The A_GETSTATS command
+ *	is used to retrive this data from the slave.
+ */
+typedef struct asystats {
+	unsigned long	opens;
+	unsigned long	txchars;
+	unsigned long	rxchars;
+	unsigned long	txringq;
+	unsigned long	rxringq;
+	unsigned long	txmsgs;
+	unsigned long	rxmsgs;
+	unsigned long	overruns;
+	unsigned long	framing;
+	unsigned long	parity;
+	unsigned long	ringover;
+	unsigned long	lost;
+	unsigned long	rxstart;
+	unsigned long	rxstop;
+	unsigned long	txstart;
+	unsigned long	txstop;
+	unsigned long	dcdcnt;
+	unsigned long	dtrcnt;
+	unsigned long	ctscnt;
+	unsigned long	rtscnt;
+	unsigned long	dsrcnt;
+	unsigned long	ricnt;
+	unsigned long	txbreaks;
+	unsigned long	rxbreaks;
+	unsigned long	signals;
+	unsigned long	state;
+} asystats_t;
+
+/*****************************************************************************/
+
+/*
+ *	All command and control communication with a device on the slave is
+ *	via a control block in shared memory. Each device has its own control
+ *	block, defined by the following structure. The control block allows
+ *	the host to open, close and control the device on the slave.
+ */
+typedef struct cdkctrl {
+	unsigned char	open;
+	unsigned char	close;
+	unsigned long	openarg;
+	unsigned long	closearg;
+	unsigned long	cmd;
+	unsigned long	status;
+	unsigned long	args[32];
+} cdkctrl_t;
+
+/*
+ *	Each device on the slave passes data to and from the host via a ring
+ *	queue in shared memory. Define a ring queue structure to hold the
+ *	vital information about each ring queue. Two ring queues will be
+ *	allocated for each port, one for reveice data and one for transmit
+ *	data.
+ */
+typedef struct cdkasyrq {
+	unsigned long	offset;
+	unsigned short	size;
+	unsigned short	head;
+	unsigned short	tail;
+} cdkasyrq_t;
+
+/*
+ *	Each asynchronous port is defined in shared memory by the following
+ *	structure. It contains a control block to command a device, and also
+ *	the neccessary data channel information as well.
+ */
+typedef struct cdkasy {
+	cdkctrl_t	ctrl;
+	unsigned short	notify;
+	asynotify_t	changed;
+	unsigned short	receive;
+	cdkasyrq_t	rxq;
+	unsigned short	transmit;
+	cdkasyrq_t	txq;
+} cdkasy_t;
+
+#pragma	pack()
+
+/*****************************************************************************/
+
+/*
+ *	Define the set of ioctls used by the driver to do special things
+ *	to the board. These include interrupting it, and initializeing
+ *	the driver after board startup and shutdown.
+ */
+#define	STLCMD		(((unsigned long) 's') << 8)
+
+#define	STL_BINTR	(STLCMD | 20)
+#define	STL_BSTART	(STLCMD | 21)
+#define	STL_BSTOP	(STLCMD | 22)
+#define	STL_BRESET	(STLCMD | 23)
+
+/*****************************************************************************/
+#endif