patch-1.3.94 linux/arch/m68k/fpsp040/util.S

Next file: linux/arch/m68k/fpsp040/x_bsun.S
Previous file: linux/arch/m68k/fpsp040/tbldo.S
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v1.3.93/linux/arch/m68k/fpsp040/util.S linux/arch/m68k/fpsp040/util.S
@@ -0,0 +1,748 @@
+|
+|	util.sa 3.7 7/29/91
+|
+|	This file contains routines used by other programs.
+|
+|	ovf_res: used by overflow to force the correct
+|		 result. ovf_r_k, ovf_r_x2, ovf_r_x3 are 
+|		 derivatives of this routine.
+|	get_fline: get user's opcode word
+|	g_dfmtou: returns the destination format.
+|	g_opcls: returns the opclass of the float instruction.
+|	g_rndpr: returns the rounding precision. 
+|	reg_dest: write byte, word, or long data to Dn
+|
+|
+|		Copyright (C) Motorola, Inc. 1990
+|			All Rights Reserved
+|
+|	THIS IS UNPUBLISHED PROPRIETARY SOURCE CODE OF MOTOROLA 
+|	The copyright notice above does not evidence any  
+|	actual or intended publication of such source code.
+
+|UTIL	idnt    2,1 | Motorola 040 Floating Point Software Package
+
+	|section	8
+
+	.include "fpsp.h"
+
+	|xref	mem_read
+
+	.global	g_dfmtou
+	.global	g_opcls
+	.global	g_rndpr
+	.global	get_fline
+	.global	reg_dest
+
+|
+| Final result table for ovf_res. Note that the negative counterparts
+| are unnecessary as ovf_res always returns the sign separately from
+| the exponent.
+|					;+inf
+EXT_PINF:	.long	0x7fff0000,0x00000000,0x00000000,0x00000000	
+|					;largest +ext
+EXT_PLRG:	.long	0x7ffe0000,0xffffffff,0xffffffff,0x00000000	
+|					;largest magnitude +sgl in ext
+SGL_PLRG:	.long	0x407e0000,0xffffff00,0x00000000,0x00000000	
+|					;largest magnitude +dbl in ext
+DBL_PLRG:	.long	0x43fe0000,0xffffffff,0xfffff800,0x00000000	
+|					;largest -ext
+
+tblovfl:
+	.long	EXT_RN
+	.long	EXT_RZ
+	.long	EXT_RM
+	.long	EXT_RP
+	.long	SGL_RN
+	.long	SGL_RZ
+	.long	SGL_RM
+	.long	SGL_RP
+	.long	DBL_RN
+	.long	DBL_RZ
+	.long	DBL_RM
+	.long	DBL_RP
+	.long	error
+	.long	error
+	.long	error
+	.long	error
+
+
+|
+|	ovf_r_k --- overflow result calculation
+|
+| This entry point is used by kernel_ex.  
+|
+| This forces the destination precision to be extended
+|
+| Input:	operand in ETEMP
+| Output:	a result is in ETEMP (internal extended format)
+|
+	.global	ovf_r_k
+ovf_r_k:
+	lea	ETEMP(%a6),%a0	|a0 points to source operand	
+	bclrb	#sign_bit,ETEMP_EX(%a6)
+	sne	ETEMP_SGN(%a6)	|convert to internal IEEE format
+
+|
+|	ovf_r_x2 --- overflow result calculation
+|
+| This entry point used by x_ovfl.  (opclass 0 and 2)
+|
+| Input		a0  points to an operand in the internal extended format
+| Output	a0  points to the result in the internal extended format
+|
+| This sets the round precision according to the user's FPCR unless the
+| instruction is fsgldiv or fsglmul or fsadd, fdadd, fsub, fdsub, fsmul,
+| fdmul, fsdiv, fddiv, fssqrt, fsmove, fdmove, fsabs, fdabs, fsneg, fdneg.
+| If the instruction is fsgldiv of fsglmul, the rounding precision must be
+| extended.  If the instruction is not fsgldiv or fsglmul but a force-
+| precision instruction, the rounding precision is then set to the force
+| precision.
+
+	.global	ovf_r_x2
+ovf_r_x2:
+	btstb	#E3,E_BYTE(%a6)		|check for nu exception
+	beql	ovf_e1_exc		|it is cu exception
+ovf_e3_exc:
+	movew	CMDREG3B(%a6),%d0		|get the command word
+	andiw	#0x00000060,%d0		|clear all bits except 6 and 5
+	cmpil	#0x00000040,%d0
+	beql	ovff_sgl		|force precision is single
+	cmpil	#0x00000060,%d0
+	beql	ovff_dbl		|force precision is double
+	movew	CMDREG3B(%a6),%d0		|get the command word again
+	andil	#0x7f,%d0			|clear all except operation
+	cmpil	#0x33,%d0			
+	beql	ovf_fsgl		|fsglmul or fsgldiv
+	cmpil	#0x30,%d0
+	beql	ovf_fsgl		
+	bra	ovf_fpcr		|instruction is none of the above
+|					;use FPCR
+ovf_e1_exc:
+	movew	CMDREG1B(%a6),%d0		|get command word
+	andil	#0x00000044,%d0		|clear all bits except 6 and 2
+	cmpil	#0x00000040,%d0
+	beql	ovff_sgl		|the instruction is force single
+	cmpil	#0x00000044,%d0
+	beql	ovff_dbl		|the instruction is force double
+	movew	CMDREG1B(%a6),%d0		|again get the command word
+	andil	#0x0000007f,%d0		|clear all except the op code
+	cmpil	#0x00000027,%d0
+	beql	ovf_fsgl		|fsglmul
+	cmpil 	#0x00000024,%d0
+	beql	ovf_fsgl		|fsgldiv
+	bra	ovf_fpcr		|none of the above, use FPCR
+| 
+|
+| Inst is either fsgldiv or fsglmul.  Force extended precision.
+|
+ovf_fsgl:
+	clrl	%d0
+	bras	ovf_res
+
+ovff_sgl:
+	movel	#0x00000001,%d0		|set single
+	bras	ovf_res
+ovff_dbl:
+	movel	#0x00000002,%d0		|set double
+	bras	ovf_res
+|
+| The precision is in the fpcr.
+|
+ovf_fpcr:
+	bfextu	FPCR_MODE(%a6){#0:#2},%d0 |set round precision
+	bras	ovf_res
+	
+|
+|
+|	ovf_r_x3 --- overflow result calculation
+|
+| This entry point used by x_ovfl. (opclass 3 only)
+|
+| Input		a0  points to an operand in the internal extended format
+| Output	a0  points to the result in the internal extended format
+|
+| This sets the round precision according to the destination size.
+|
+	.global	ovf_r_x3
+ovf_r_x3:
+	bsr	g_dfmtou	|get dest fmt in d0{1:0}
+|				;for fmovout, the destination format
+|				;is the rounding precision
+
+|
+|	ovf_res --- overflow result calculation
+|
+| Input:
+|	a0 	points to operand in internal extended format
+| Output:
+|	a0 	points to result in internal extended format
+|
+	.global	ovf_res
+ovf_res:
+	lsll	#2,%d0		|move round precision to d0{3:2}
+	bfextu	FPCR_MODE(%a6){#2:#2},%d1 |set round mode
+	orl	%d1,%d0		|index is fmt:mode in d0{3:0}
+	leal	tblovfl,%a1	|load a1 with table address
+	movel	%a1@(%d0:l:4),%a1	|use d0 as index to the table
+	jmp	(%a1)		|go to the correct routine
+|
+|case DEST_FMT = EXT
+|
+EXT_RN:
+	leal	EXT_PINF,%a1	|answer is +/- infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bra	set_sign	|now go set the sign	
+EXT_RZ:
+	leal	EXT_PLRG,%a1	|answer is +/- large number
+	bra	set_sign	|now go set the sign
+EXT_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	e_rm_pos
+e_rm_neg:
+	leal	EXT_PINF,%a1	|answer is negative infinity
+	orl	#neginf_mask,USER_FPSR(%a6)
+	bra	end_ovfr
+e_rm_pos:
+	leal	EXT_PLRG,%a1	|answer is large positive number
+	bra	end_ovfr
+EXT_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	e_rp_pos
+e_rp_neg:
+	leal	EXT_PLRG,%a1	|answer is large negative number
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bra	end_ovfr
+e_rp_pos:
+	leal	EXT_PINF,%a1	|answer is positive infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bra	end_ovfr
+|
+|case DEST_FMT = DBL
+|
+DBL_RN:
+	leal	EXT_PINF,%a1	|answer is +/- infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bra	set_sign
+DBL_RZ:
+	leal	DBL_PLRG,%a1	|answer is +/- large number
+	bra	set_sign	|now go set the sign
+DBL_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	d_rm_pos
+d_rm_neg:
+	leal	EXT_PINF,%a1	|answer is negative infinity
+	orl	#neginf_mask,USER_FPSR(%a6)
+	bra	end_ovfr	|inf is same for all precisions (ext,dbl,sgl)
+d_rm_pos:
+	leal	DBL_PLRG,%a1	|answer is large positive number
+	bra	end_ovfr
+DBL_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	d_rp_pos
+d_rp_neg:
+	leal	DBL_PLRG,%a1	|answer is large negative number
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bra	end_ovfr
+d_rp_pos:
+	leal	EXT_PINF,%a1	|answer is positive infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bra	end_ovfr
+|
+|case DEST_FMT = SGL
+|
+SGL_RN:
+	leal	EXT_PINF,%a1	|answer is +/-  infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bras	set_sign
+SGL_RZ:
+	leal	SGL_PLRG,%a1	|anwer is +/- large number
+	bras	set_sign
+SGL_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	s_rm_pos
+s_rm_neg:
+	leal	EXT_PINF,%a1	|answer is negative infinity
+	orl	#neginf_mask,USER_FPSR(%a6)
+	bras	end_ovfr
+s_rm_pos:
+	leal	SGL_PLRG,%a1	|answer is large positive number
+	bras	end_ovfr
+SGL_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	s_rp_pos
+s_rp_neg:
+	leal	SGL_PLRG,%a1	|answer is large negative number
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bras	end_ovfr
+s_rp_pos:
+	leal	EXT_PINF,%a1	|answer is postive infinity
+	bsetb	#inf_bit,FPSR_CC(%a6)
+	bras	end_ovfr
+
+set_sign:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	end_ovfr
+neg_sign:
+	bsetb	#neg_bit,FPSR_CC(%a6)
+
+end_ovfr:
+	movew	LOCAL_EX(%a1),LOCAL_EX(%a0) |do not overwrite sign
+	movel	LOCAL_HI(%a1),LOCAL_HI(%a0)
+	movel	LOCAL_LO(%a1),LOCAL_LO(%a0)
+	rts
+
+
+|
+|	ERROR
+|
+error:
+	rts
+|
+|	get_fline --- get f-line opcode of interrupted instruction
+|
+|	Returns opcode in the low word of d0.
+|
+get_fline:
+	movel	USER_FPIAR(%a6),%a0	|opcode address
+	movel	#0,-(%a7)	|reserve a word on the stack
+	leal	2(%a7),%a1	|point to low word of temporary
+	movel	#2,%d0		|count
+	bsrl	mem_read
+	movel	(%a7)+,%d0
+	rts
+|
+| 	g_rndpr --- put rounding precision in d0{1:0}
+|	
+|	valid return codes are:
+|		00 - extended 
+|		01 - single
+|		10 - double
+|
+| begin
+| get rounding precision (cmdreg3b{6:5})
+| begin
+|  case	opclass = 011 (move out)
+|	get destination format - this is the also the rounding precision
+|
+|  case	opclass = 0x0
+|	if E3
+|	    *case RndPr(from cmdreg3b{6:5} = 11  then RND_PREC = DBL
+|	    *case RndPr(from cmdreg3b{6:5} = 10  then RND_PREC = SGL
+|	     case RndPr(from cmdreg3b{6:5} = 00 | 01
+|		use precision from FPCR{7:6}
+|			case 00 then RND_PREC = EXT
+|			case 01 then RND_PREC = SGL
+|			case 10 then RND_PREC = DBL
+|	else E1
+|	     use precision in FPCR{7:6}
+|	     case 00 then RND_PREC = EXT
+|	     case 01 then RND_PREC = SGL
+|	     case 10 then RND_PREC = DBL
+| end
+|
+g_rndpr:
+	bsr	g_opcls		|get opclass in d0{2:0}
+	cmpw	#0x0003,%d0	|check for opclass 011
+	bnes	op_0x0
+
+|
+| For move out instructions (opclass 011) the destination format
+| is the same as the rounding precision.  Pass results from g_dfmtou.
+|
+	bsr 	g_dfmtou	
+	rts
+op_0x0:
+	btstb	#E3,E_BYTE(%a6)
+	beql	unf_e1_exc	|branch to e1 underflow
+unf_e3_exc:
+	movel	CMDREG3B(%a6),%d0	|rounding precision in d0{10:9}
+	bfextu	%d0{#9:#2},%d0	|move the rounding prec bits to d0{1:0}
+	cmpil	#0x2,%d0
+	beql	unff_sgl	|force precision is single
+	cmpil	#0x3,%d0		|force precision is double
+	beql	unff_dbl
+	movew	CMDREG3B(%a6),%d0	|get the command word again
+	andil	#0x7f,%d0		|clear all except operation
+	cmpil	#0x33,%d0			
+	beql	unf_fsgl	|fsglmul or fsgldiv
+	cmpil	#0x30,%d0
+	beql	unf_fsgl	|fsgldiv or fsglmul
+	bra	unf_fpcr
+unf_e1_exc:
+	movel	CMDREG1B(%a6),%d0	|get 32 bits off the stack, 1st 16 bits
+|				;are the command word
+	andil	#0x00440000,%d0	|clear all bits except bits 6 and 2
+	cmpil	#0x00400000,%d0
+	beql	unff_sgl	|force single
+	cmpil	#0x00440000,%d0	|force double
+	beql	unff_dbl
+	movel	CMDREG1B(%a6),%d0	|get the command word again
+	andil	#0x007f0000,%d0	|clear all bits except the operation
+	cmpil	#0x00270000,%d0
+	beql	unf_fsgl	|fsglmul
+	cmpil	#0x00240000,%d0
+	beql	unf_fsgl	|fsgldiv
+	bra	unf_fpcr
+
+|
+| Convert to return format.  The values from cmdreg3b and the return
+| values are:
+|	cmdreg3b	return	     precision
+|	--------	------	     ---------
+|	  00,01		  0		ext
+|	   10		  1		sgl
+|	   11		  2		dbl
+| Force single
+|
+unff_sgl:
+	movel	#1,%d0		|return 1
+	rts
+|
+| Force double
+|
+unff_dbl:
+	movel	#2,%d0		|return 2
+	rts
+|
+| Force extended
+|
+unf_fsgl:
+	movel	#0,%d0		
+	rts
+|
+| Get rounding precision set in FPCR{7:6}.
+|
+unf_fpcr:
+	movel	USER_FPCR(%a6),%d0 |rounding precision bits in d0{7:6}
+	bfextu	%d0{#24:#2},%d0	|move the rounding prec bits to d0{1:0}
+	rts
+|
+|	g_opcls --- put opclass in d0{2:0}
+|
+g_opcls:
+	btstb	#E3,E_BYTE(%a6)
+	beqs	opc_1b		|if set, go to cmdreg1b
+opc_3b:
+	clrl	%d0		|if E3, only opclass 0x0 is possible
+	rts
+opc_1b:
+	movel	CMDREG1B(%a6),%d0
+	bfextu	%d0{#0:#3},%d0	|shift opclass bits d0{31:29} to d0{2:0}
+	rts
+|
+|	g_dfmtou --- put destination format in d0{1:0}
+|
+|	If E1, the format is from cmdreg1b{12:10}
+|	If E3, the format is extended.
+|
+|	Dest. Fmt.	
+|		extended  010 -> 00
+|		single    001 -> 01
+|		double    101 -> 10
+|
+g_dfmtou:
+	btstb	#E3,E_BYTE(%a6)
+	beqs	op011
+	clrl	%d0		|if E1, size is always ext
+	rts
+op011:
+	movel	CMDREG1B(%a6),%d0
+	bfextu	%d0{#3:#3},%d0	|dest fmt from cmdreg1b{12:10}
+	cmpb	#1,%d0		|check for single
+	bnes	not_sgl
+	movel	#1,%d0
+	rts
+not_sgl:
+	cmpb	#5,%d0		|check for double
+	bnes	not_dbl
+	movel	#2,%d0
+	rts
+not_dbl:
+	clrl	%d0		|must be extended
+	rts
+
+|
+|
+| Final result table for unf_sub. Note that the negative counterparts
+| are unnecessary as unf_sub always returns the sign separately from
+| the exponent.
+|					;+zero
+EXT_PZRO:	.long	0x00000000,0x00000000,0x00000000,0x00000000	
+|					;+zero
+SGL_PZRO:	.long	0x3f810000,0x00000000,0x00000000,0x00000000	
+|					;+zero
+DBL_PZRO:	.long	0x3c010000,0x00000000,0x00000000,0x00000000	
+|					;smallest +ext denorm
+EXT_PSML:	.long	0x00000000,0x00000000,0x00000001,0x00000000	
+|					;smallest +sgl denorm
+SGL_PSML:	.long	0x3f810000,0x00000100,0x00000000,0x00000000	
+|					;smallest +dbl denorm
+DBL_PSML:	.long	0x3c010000,0x00000000,0x00000800,0x00000000	
+|
+|	UNF_SUB --- underflow result calculation
+|
+| Input:
+|	d0 	contains round precision
+|	a0	points to input operand in the internal extended format
+|
+| Output:
+|	a0 	points to correct internal extended precision result.
+|
+
+tblunf:
+	.long	uEXT_RN
+	.long	uEXT_RZ
+	.long	uEXT_RM
+	.long	uEXT_RP
+	.long	uSGL_RN
+	.long	uSGL_RZ
+	.long	uSGL_RM
+	.long	uSGL_RP
+	.long	uDBL_RN
+	.long	uDBL_RZ
+	.long	uDBL_RM
+	.long	uDBL_RP
+	.long	uDBL_RN
+	.long	uDBL_RZ
+	.long	uDBL_RM
+	.long	uDBL_RP
+
+	.global	unf_sub
+unf_sub:
+	lsll	#2,%d0		|move round precision to d0{3:2}
+	bfextu	FPCR_MODE(%a6){#2:#2},%d1 |set round mode
+	orl	%d1,%d0		|index is fmt:mode in d0{3:0}
+	leal	tblunf,%a1	|load a1 with table address
+	movel	%a1@(%d0:l:4),%a1	|use d0 as index to the table
+	jmp	(%a1)		|go to the correct routine
+|
+|case DEST_FMT = EXT
+|
+uEXT_RN:
+	leal	EXT_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	uset_sign	|now go set the sign	
+uEXT_RZ:
+	leal	EXT_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	uset_sign	|now go set the sign
+uEXT_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative underflow
+	beqs	ue_rm_pos
+ue_rm_neg:
+	leal	EXT_PSML,%a1	|answer is negative smallest denorm
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bra	end_unfr
+ue_rm_pos:
+	leal	EXT_PZRO,%a1	|answer is positive zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	end_unfr
+uEXT_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative underflow
+	beqs	ue_rp_pos
+ue_rp_neg:
+	leal	EXT_PZRO,%a1	|answer is negative zero
+	oril	#negz_mask,USER_FPSR(%a6)
+	bra	end_unfr
+ue_rp_pos:
+	leal	EXT_PSML,%a1	|answer is positive smallest denorm
+	bra	end_unfr
+|
+|case DEST_FMT = DBL
+|
+uDBL_RN:
+	leal	DBL_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	uset_sign
+uDBL_RZ:
+	leal	DBL_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	uset_sign	|now go set the sign
+uDBL_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	ud_rm_pos
+ud_rm_neg:
+	leal	DBL_PSML,%a1	|answer is smallest denormalized negative
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bra	end_unfr
+ud_rm_pos:
+	leal	DBL_PZRO,%a1	|answer is positive zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bra	end_unfr
+uDBL_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	ud_rp_pos
+ud_rp_neg:
+	leal	DBL_PZRO,%a1	|answer is negative zero
+	oril	#negz_mask,USER_FPSR(%a6)
+	bra	end_unfr
+ud_rp_pos:
+	leal	DBL_PSML,%a1	|answer is smallest denormalized negative
+	bra	end_unfr
+|
+|case DEST_FMT = SGL
+|
+uSGL_RN:
+	leal	SGL_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bras	uset_sign
+uSGL_RZ:
+	leal	SGL_PZRO,%a1	|answer is +/- zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bras	uset_sign
+uSGL_RM:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	us_rm_pos
+us_rm_neg:
+	leal	SGL_PSML,%a1	|answer is smallest denormalized negative
+	bsetb	#neg_bit,FPSR_CC(%a6)
+	bras	end_unfr
+us_rm_pos:
+	leal	SGL_PZRO,%a1	|answer is positive zero
+	bsetb	#z_bit,FPSR_CC(%a6)
+	bras	end_unfr
+uSGL_RP:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	us_rp_pos
+us_rp_neg:
+	leal	SGL_PZRO,%a1	|answer is negative zero
+	oril	#negz_mask,USER_FPSR(%a6)
+	bras	end_unfr
+us_rp_pos:
+	leal	SGL_PSML,%a1	|answer is smallest denormalized positive
+	bras	end_unfr
+
+uset_sign:
+	tstb	LOCAL_SGN(%a0)	|if negative overflow
+	beqs	end_unfr
+uneg_sign:
+	bsetb	#neg_bit,FPSR_CC(%a6)
+
+end_unfr:
+	movew	LOCAL_EX(%a1),LOCAL_EX(%a0) |be careful not to overwrite sign
+	movel	LOCAL_HI(%a1),LOCAL_HI(%a0)
+	movel	LOCAL_LO(%a1),LOCAL_LO(%a0)
+	rts
+|
+|	reg_dest --- write byte, word, or long data to Dn
+|
+|
+| Input:
+|	L_SCR1: Data 
+|	d1:     data size and dest register number formatted as:
+|
+|	32		5    4     3     2     1     0
+|       -----------------------------------------------
+|       |        0        |    Size   |  Dest Reg #   |
+|       -----------------------------------------------
+|
+|	Size is:
+|		0 - Byte
+|		1 - Word
+|		2 - Long/Single
+|
+pregdst:
+	.long	byte_d0
+	.long	byte_d1
+	.long	byte_d2
+	.long	byte_d3
+	.long	byte_d4
+	.long	byte_d5
+	.long	byte_d6
+	.long	byte_d7
+	.long	word_d0
+	.long	word_d1
+	.long	word_d2
+	.long	word_d3
+	.long	word_d4
+	.long	word_d5
+	.long	word_d6
+	.long	word_d7
+	.long	long_d0
+	.long	long_d1
+	.long	long_d2
+	.long	long_d3
+	.long	long_d4
+	.long	long_d5
+	.long	long_d6
+	.long	long_d7
+
+reg_dest:
+	leal	pregdst,%a0
+	movel	%a0@(%d1:l:4),%a0
+	jmp	(%a0)
+
+byte_d0:
+	moveb	L_SCR1(%a6),USER_D0+3(%a6)
+	rts
+byte_d1:
+	moveb	L_SCR1(%a6),USER_D1+3(%a6)
+	rts
+byte_d2:
+	moveb	L_SCR1(%a6),%d2
+	rts
+byte_d3:
+	moveb	L_SCR1(%a6),%d3
+	rts
+byte_d4:
+	moveb	L_SCR1(%a6),%d4
+	rts
+byte_d5:
+	moveb	L_SCR1(%a6),%d5
+	rts
+byte_d6:
+	moveb	L_SCR1(%a6),%d6
+	rts
+byte_d7:
+	moveb	L_SCR1(%a6),%d7
+	rts
+word_d0:
+	movew	L_SCR1(%a6),USER_D0+2(%a6)
+	rts
+word_d1:
+	movew	L_SCR1(%a6),USER_D1+2(%a6)
+	rts
+word_d2:
+	movew	L_SCR1(%a6),%d2
+	rts
+word_d3:
+	movew	L_SCR1(%a6),%d3
+	rts
+word_d4:
+	movew	L_SCR1(%a6),%d4
+	rts
+word_d5:
+	movew	L_SCR1(%a6),%d5
+	rts
+word_d6:
+	movew	L_SCR1(%a6),%d6
+	rts
+word_d7:
+	movew	L_SCR1(%a6),%d7
+	rts
+long_d0:
+	movel	L_SCR1(%a6),USER_D0(%a6)
+	rts
+long_d1:
+	movel	L_SCR1(%a6),USER_D1(%a6)
+	rts
+long_d2:
+	movel	L_SCR1(%a6),%d2
+	rts
+long_d3:
+	movel	L_SCR1(%a6),%d3
+	rts
+long_d4:
+	movel	L_SCR1(%a6),%d4
+	rts
+long_d5:
+	movel	L_SCR1(%a6),%d5
+	rts
+long_d6:
+	movel	L_SCR1(%a6),%d6
+	rts
+long_d7:
+	movel	L_SCR1(%a6),%d7
+	rts
+	|end
FUNET's LINUX-ADM group, [email protected]
TCL-scripts by Sam Shen, [email protected] with Sam's (original) version
of this