patch-2.3.36 linux/include/linux/ixjuser.h

Next file: linux/include/linux/major.h
Previous file: linux/include/linux/irda.h
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.3.35/linux/include/linux/ixjuser.h linux/include/linux/ixjuser.h
@@ -0,0 +1,629 @@
+/*
+ *    ixjuser.h
+ *
+ *    User-space include file for the Internet PhoneJACK and
+ *    Internet LineJACK Telephony Cards.
+ *
+ *    (c) Copyright 1999 Quicknet Technologies, Inc.
+ *
+ *    This program is free software; you can redistribute it and/or
+ *    modify it under the terms of the GNU General Public License
+ *    as published by the Free Software Foundation; either version
+ *    2 of the License, or (at your option) any later version.
+ *
+ * Author:          Ed Okerson, <[email protected]>
+ *    
+ * Contributors:    Greg Herlein, <[email protected]>
+ *                  David W. Erhart, <[email protected]>
+ *                  John Sellers, <[email protected]>
+ *                  Mike Preston, <[email protected]>
+ *
+ * More information about the hardware related to this driver can be found
+ * at our website:    http://www.quicknet.net
+ *
+ * Fixes:
+ */
+
+static char ixjuser_h_rcsid[] = "$Id: ixjuser.h,v 3.4 1999/12/16 22:18:36 root Exp root $";
+
+#include <linux/telephony.h>
+
+/***************************************************************************
+
+  If you use the IXJCTL_TESTRAM command, the card must be power
+  cycled to reset the SRAM values before futher use.
+
+***************************************************************************/
+#define IXJCTL_DSP_RESET 		_IO  ('q', 0xC0)
+
+#define IXJCTL_RING         PHONE_RING
+#define IXJCTL_HOOKSTATE    PHONE_HOOKSTATE
+#define IXJCTL_MAXRINGS			PHONE_MAXRINGS
+#define IXJCTL_RING_CADENCE	PHONE_RING_CADENCE
+#define IXJCTL_RING_START		PHONE_RING_START
+#define IXJCTL_RING_STOP		PHONE_RING_STOP
+
+#define IXJCTL_CARDTYPE			_IOR ('q', 0xC1, int)
+#define IXJCTL_SERIAL			  _IOR ('q', 0xC2, int)
+#define IXJCTL_DSP_TYPE     _IOR ('q', 0xC3, int)
+#define IXJCTL_DSP_VERSION  _IOR ('q', 0xC4, int)
+#define IXJCTL_DSP_IDLE			_IO  ('q', 0xC5)
+#define IXJCTL_TESTRAM			_IO  ('q', 0xC6)
+
+/******************************************************************************
+*
+* This group of IOCTLs deal with the record settings of the DSP
+*
+* The IXJCTL_REC_DEPTH command sets the internal buffer depth of the DSP.
+* Setting a lower depth reduces latency, but increases the demand of the
+* application to service the driver without frame loss.  The DSP has 480
+* bytes of physical buffer memory for the record channel so the true
+* maximum limit is determined by how many frames will fit in the buffer.
+*
+* 1 uncompressed (480 byte) 16-bit linear frame.
+* 2 uncompressed (240 byte) 8-bit A-law/mu-law frames.
+* 15 TrueSpeech 8.5 frames.
+* 20 TrueSpeech 6.3,5.3,4.8 or 4.1 frames.
+*
+* The default in the driver is currently set to 2 frames.
+*
+* The IXJCTL_REC_VOLUME and IXJCTL_PLAY_VOLUME commands both use a Q8
+* number as a parameter, 0x100 scales the signal by 1.0, 0x200 scales the
+* signal by 2.0, 0x80 scales the signal by 0.5.  No protection is given
+* against over-scaling, if the multiplication factor times the input
+* signal exceeds 16 bits, overflow distortion will occur.  The default
+* setting is 0x100 (1.0).
+*
+* The IXJCTL_REC_LEVEL returns the average signal level (not r.m.s.) on
+* the most recently recorded frame as a 16 bit value.
+******************************************************************************/
+
+#define IXJCTL_REC_CODEC                PHONE_REC_CODEC
+#define IXJCTL_REC_START                PHONE_REC_START
+#define IXJCTL_REC_STOP                 PHONE_REC_STOP
+#define IXJCTL_REC_DEPTH		PHONE_REC_DEPTH
+#define IXJCTL_FRAME			PHONE_FRAME
+#define IXJCTL_REC_VOLUME		PHONE_REC_VOLUME
+#define IXJCTL_REC_LEVEL		PHONE_REC_LEVEL
+
+typedef enum {
+	f300_640 = 4, f300_500, f1100, f350, f400, f480, f440, f620, f20_50,
+	f133_200, f300, f300_420, f330, f300_425, f330_440, f340, f350_400,
+	f350_440, f350_450, f360, f380_420, f392, f400_425, f400_440, f400_450,
+	f420, f425, f425_450, f425_475, f435, f440_450, f440_480, f445, f450,
+	f452, f475, f480_620, f494, f500, f520, f523, f525, f540_660, f587,
+	f590, f600, f660, f700, f740, f750, f750_1450, f770, f800, f816, f850,
+	f857_1645, f900, f900_1300, f935_1215, f941_1477, f942, f950, f950_1400,
+	f975, f1000, f1020, f1050, f1100_1750, f1140, f1200, f1209, f1330, f1336,
+	lf1366, f1380, f1400, f1477, f1600, f1633_1638, f1800, f1860
+} IXJ_FILTER_FREQ;
+
+typedef struct {
+	unsigned int filter;
+	IXJ_FILTER_FREQ freq;
+	char enable;
+} IXJ_FILTER;
+
+#define IXJCTL_SET_FILTER		_IOW ('q', 0xC7, IXJ_FILTER *)
+#define IXJCTL_GET_FILTER_HIST		_IOW ('q', 0xC8, int)
+/******************************************************************************
+*
+* This IOCTL allows you to reassign values in the tone index table.  The
+* tone table has 32 entries (0 - 31), but the driver only allows entries
+* 13 - 27 to be modified, entry 0 is reserved for silence and 1 - 12 are
+* the standard DTMF digits and 28 - 31 are the DTMF tones for A, B, C & D.
+* The positions used internally for Call Progress Tones are as follows:
+*    Dial Tone   - 25
+*    Ring Back   - 26
+*    Busy Signal - 27
+*
+* The freq values are calculated as:
+* freq = cos(2 * PI * frequency / 8000)
+*
+* The most commonly needed values are already calculated and listed in the
+* enum IXJ_TONE_FREQ.  Each tone index can have two frequencies with
+* different gains, if you are only using a single frequency set the unused
+* one to 0.
+*
+* The gain values range from 0 to 15 indicating +6dB to -24dB in 2dB
+* increments.
+*
+******************************************************************************/
+
+typedef enum {
+	hz20 = 0x7ffa,
+	hz50 = 0x7fe5,
+	hz133 = 0x7f4c,
+	hz200 = 0x7e6b,
+	hz261 = 0x7d50,		/* .63 C1  */
+	hz277 = 0x7cfa,		/* .18 CS1 */
+	hz293 = 0x7c9f,		/* .66 D1  */
+	hz300 = 0x7c75,
+	hz311 = 0x7c32,		/* .13 DS1 */
+	hz329 = 0x7bbf,		/* .63 E1  */
+	hz330 = 0x7bb8,
+	hz340 = 0x7b75,
+	hz349 = 0x7b37,		/* .23 F1  */
+	hz350 = 0x7b30,
+	hz360 = 0x7ae9,
+	hz369 = 0x7aa8,		/* .99 FS1 */
+	hz380 = 0x7a56,
+	hz392 = 0x79fa,		/* .00 G1  */
+	hz400 = 0x79bb,
+	hz415 = 0x7941,		/* .30 GS1 */
+	hz420 = 0x7918,
+	hz425 = 0x78ee,
+	hz435 = 0x7899,
+	hz440 = 0x786d,		/* .00 A1  */
+	hz445 = 0x7842,
+	hz450 = 0x7815,
+	hz452 = 0x7803,
+	hz466 = 0x7784,		/* .16 AS1 */
+	hz475 = 0x7731,
+	hz480 = 0x7701,
+	hz493 = 0x7685,		/* .88 B1  */
+	hz494 = 0x767b,
+	hz500 = 0x7640,
+	hz520 = 0x7578,
+	hz523 = 0x7559,		/* .25 C2  */
+	hz525 = 0x7544,
+	hz540 = 0x74a7,
+	hz554 = 0x7411,		/* .37 CS2 */
+	hz587 = 0x72a1,		/* .33 D2  */
+	hz590 = 0x727f,
+	hz600 = 0x720b,
+	hz620 = 0x711e,
+	hz622 = 0x7106,		/* .25 DS2 */
+	hz659 = 0x6f3b,		/* .26 E2  */
+	hz660 = 0x6f2e,
+	hz698 = 0x6d3d,		/* .46 F2  */
+	hz700 = 0x6d22,
+	hz739 = 0x6b09,		/* .99 FS2 */
+	hz740 = 0x6afa,
+	hz750 = 0x6a6c,
+	hz770 = 0x694b,
+	hz783 = 0x688b,		/* .99 G2  */
+	hz800 = 0x678d,
+	hz816 = 0x6698,
+	hz830 = 0x65bf,		/* .61 GS2 */
+	hz850 = 0x6484,
+	hz857 = 0x6414,
+	hz880 = 0x629f,		/* .00 A2  */
+	hz900 = 0x6154,
+	hz932 = 0x5f35,		/* .33 AS2 */
+	hz935 = 0x5f01,
+	hz941 = 0x5e9a,
+	hz942 = 0x5e88,
+	hz950 = 0x5dfd,
+	hz975 = 0x5c44,
+	hz1000 = 0x5a81,
+	hz1020 = 0x5912,
+	hz1050 = 0x56e2,
+	hz1100 = 0x5320,
+	hz1140 = 0x5007,
+	hz1200 = 0x4b3b,
+	hz1209 = 0x4a80,
+	hz1215 = 0x4a02,
+	hz1250 = 0x471c,
+	hz1300 = 0x42e0,
+	hz1330 = 0x4049,
+	hz1336 = 0x3fc4,
+	hz1366 = 0x3d22,
+	hz1380 = 0x3be4,
+	hz1400 = 0x3a1b,
+	hz1450 = 0x3596,
+	hz1477 = 0x331c,
+	hz1500 = 0x30fb,
+	hz1600 = 0x278d,
+	hz1633 = 0x2462,
+	hz1638 = 0x23e7,
+	hz1645 = 0x233a,
+	hz1750 = 0x18f8,
+	hz1800 = 0x1405,
+	hz1860 = 0xe0b,
+	hz2100 = 0xf5f6,
+	hz2450 = 0xd3b3
+} IXJ_FREQ;
+
+typedef enum {
+	C1 = hz261,
+	CS1 = hz277,
+	D1 = hz293,
+	DS1 = hz311,
+	E1 = hz329,
+	F1 = hz349,
+	FS1 = hz369,
+	G1 = hz392,
+	GS1 = hz415,
+	A1 = hz440,
+	AS1 = hz466,
+	B1 = hz493,
+	C2 = hz523,
+	CS2 = hz554,
+	D2 = hz587,
+	DS2 = hz622,
+	E2 = hz659,
+	F2 = hz698,
+	FS2 = hz739,
+	G2 = hz783,
+	GS2 = hz830,
+	A2 = hz880,
+	AS2 = hz932,
+} IXJ_NOTE;
+
+typedef struct {
+	int tone_index;
+	int freq0;
+	int gain0;
+	int freq1;
+	int gain1;
+} IXJ_TONE;
+
+#define IXJCTL_INIT_TONE		_IOW ('q', 0xC9, IXJ_TONE *)
+
+/******************************************************************************
+*
+* The IXJCTL_TONE_CADENCE ioctl defines tone sequences used for various
+* Call Progress Tones (CPT).  This is accomplished by setting up an array of
+* IXJ_CADENCE_ELEMENT structures that sequentially define the states of
+* the tone sequence.  The tone_on_time and tone_off time are in
+* 250 microsecond intervals.  A pointer to this array is passed to the
+* driver as the ce element of an IXJ_CADENCE structure.  The elements_used
+* must be set to the number of IXJ_CADENCE_ELEMENTS in the array.  The
+* termination variable defines what to do at the end of a cadence, the
+* options are to play the cadence once and stop, to repeat the last
+* element of the cadence indefinatly, or to repeat the entire cadence
+* indefinatly.  The ce variable is a pointer to the array of IXJ_TONE
+* structures.  If the freq0 variable is non-zero, the tone table contents
+* for the tone_index are updated to the frequencies and gains defined.  It
+* should be noted that DTMF tones cannot be reassigned, so if DTMF tone
+* table indexs are used in a cadence the frequency and gain variables will
+* be ignored.
+*
+* If the array elements contain frequency parameters the driver will
+* initialize the needed tone table elements and begin playing the tone,
+* there is no preset limit on the number of elements in the cadence.  If
+* there is more than one frequency used in the cadence, sequential elements
+* of different frequencies MUST use different tone table indexes.  Only one
+* cadence can be played at a time.  It is possible to build complex
+* cadences with multiple frequencies using 2 tone table indexes by
+* alternating between them.
+*
+******************************************************************************/
+
+typedef struct {
+	int index;
+	int tone_on_time;
+	int tone_off_time;
+	int freq0;
+	int gain0;
+	int freq1;
+	int gain1;
+} IXJ_CADENCE_ELEMENT;
+
+typedef enum {
+	PLAY_ONCE,
+	REPEAT_LAST_ELEMENT,
+	REPEAT_ALL
+} IXJ_CADENCE_TERM;
+
+typedef struct {
+	int elements_used;
+	IXJ_CADENCE_TERM termination;
+	IXJ_CADENCE_ELEMENT *ce;
+} IXJ_CADENCE;
+
+#define IXJCTL_TONE_CADENCE		_IOW ('q', 0xCA, IXJ_CADENCE *)
+/******************************************************************************
+*
+* This group of IOCTLs deal with the playback settings of the DSP
+*
+******************************************************************************/
+
+#define IXJCTL_PLAY_CODEC               PHONE_PLAY_CODEC
+#define IXJCTL_PLAY_START               PHONE_PLAY_START
+#define IXJCTL_PLAY_STOP                PHONE_PLAY_STOP
+#define IXJCTL_PLAY_DEPTH		PHONE_PLAY_DEPTH
+#define IXJCTL_PLAY_VOLUME		PHONE_PLAY_VOLUME
+#define IXJCTL_PLAY_LEVEL		PHONE_PLAY_LEVEL
+
+/******************************************************************************
+*
+* This group of IOCTLs deal with the Acoustic Echo Cancellation settings
+* of the DSP
+*
+* Issueing the IXJCTL_AEC_START command with a value of AEC_OFF has the
+* same effect as IXJCTL_AEC_STOP.  This is to simplify slider bar
+* controls.  IXJCTL_AEC_GET_LEVEL returns the current setting of the AEC.
+******************************************************************************/
+#define IXJCTL_AEC_START		_IOW ('q', 0xCB, int)
+#define IXJCTL_AEC_STOP			_IO  ('q', 0xCC)
+#define IXJCTL_AEC_GET_LEVEL		_IO  ('q', 0xCD)
+
+#define AEC_OFF   0
+#define AEC_LOW   1
+#define AEC_MED   2
+#define AEC_HIGH  3
+/******************************************************************************
+*
+* Call Progress Tones, DTMF, etc.
+* IXJCTL_DTMF_OOB determines if dtmf signaling is sent as Out-Of-Band
+* only.  If you pass a 1, dtmf is suppressed from the audio stream.
+* Tone on and off times are in 250 microsecond intervals so
+* ioctl(ixj1, IXJCTL_SET_TONE_ON_TIME, 360);
+* will set the tone on time of board ixj1 to 360 * 250us = 90ms
+* the default values of tone on and off times is 840 or 210ms
+******************************************************************************/
+
+#define IXJCTL_DTMF_READY		PHONE_DTMF_READY
+#define IXJCTL_GET_DTMF                 PHONE_GET_DTMF
+#define IXJCTL_GET_DTMF_ASCII           PHONE_GET_DTMF_ASCII
+#define IXJCTL_DTMF_OOB			PHONE_DTMF_OOB
+#define IXJCTL_EXCEPTION		PHONE_EXCEPTION
+#define IXJCTL_PLAY_TONE		PHONE_PLAY_TONE
+#define IXJCTL_SET_TONE_ON_TIME		PHONE_SET_TONE_ON_TIME
+#define IXJCTL_SET_TONE_OFF_TIME	PHONE_SET_TONE_OFF_TIME
+#define IXJCTL_GET_TONE_ON_TIME		PHONE_GET_TONE_ON_TIME
+#define IXJCTL_GET_TONE_OFF_TIME	PHONE_GET_TONE_OFF_TIME
+#define IXJCTL_GET_TONE_STATE		PHONE_GET_TONE_STATE
+#define IXJCTL_BUSY			PHONE_BUSY
+#define IXJCTL_RINGBACK			PHONE_RINGBACK
+#define IXJCTL_DIALTONE			PHONE_DIALTONE
+#define IXJCTL_CPT_STOP			PHONE_CPT_STOP
+
+/******************************************************************************
+* LineJack specific IOCTLs
+*
+* The lsb 4 bits of the LED argument represent the state of each of the 4
+* LED's on the LineJack
+******************************************************************************/
+
+#define IXJCTL_SET_LED			_IOW ('q', 0xCE, int)
+#define IXJCTL_MIXER			_IOW ('q', 0xCF, int)
+
+/******************************************************************************
+* 
+* The master volume controls use attenuation with 32 levels from 0 to -62dB
+* with steps of 2dB each, the defines should be OR'ed together then sent
+* as the parameter to the mixer command to change the mixer settings.
+* 
+******************************************************************************/
+#define MIXER_MASTER_L		0x0100
+#define MIXER_MASTER_R		0x0200
+#define ATT00DB			0x00
+#define ATT02DB			0x01
+#define ATT04DB			0x02
+#define ATT06DB			0x03
+#define ATT08DB			0x04
+#define ATT10DB			0x05
+#define ATT12DB			0x06
+#define ATT14DB			0x07
+#define ATT16DB			0x08
+#define ATT18DB			0x09
+#define ATT20DB			0x0A
+#define ATT22DB			0x0B
+#define ATT24DB			0x0C
+#define ATT26DB			0x0D
+#define ATT28DB			0x0E
+#define ATT30DB			0x0F
+#define ATT32DB			0x10
+#define ATT34DB			0x11
+#define ATT36DB			0x12
+#define ATT38DB			0x13
+#define ATT40DB			0x14
+#define ATT42DB			0x15
+#define ATT44DB			0x16
+#define ATT46DB			0x17
+#define ATT48DB			0x18
+#define ATT50DB			0x19
+#define ATT52DB			0x1A
+#define ATT54DB			0x1B
+#define ATT56DB			0x1C
+#define ATT58DB			0x1D
+#define ATT60DB			0x1E
+#define ATT62DB			0x1F
+#define MASTER_MUTE		0x80
+
+/******************************************************************************
+* 
+* The input volume controls use gain with 32 levels from +12dB to -50dB
+* with steps of 2dB each, the defines should be OR'ed together then sent
+* as the parameter to the mixer command to change the mixer settings.
+* 
+******************************************************************************/
+#define MIXER_PORT_CD_L		0x0600
+#define MIXER_PORT_CD_R		0x0700
+#define MIXER_PORT_LINE_IN_L	0x0800
+#define MIXER_PORT_LINE_IN_R	0x0900
+#define MIXER_PORT_POTS_REC	0x0C00
+#define MIXER_PORT_MIC		0x0E00
+
+#define GAIN12DB		0x00
+#define GAIN10DB		0x01
+#define GAIN08DB		0x02
+#define GAIN06DB		0x03
+#define GAIN04DB		0x04
+#define GAIN02DB		0x05
+#define GAIN00DB		0x06
+#define GAIN_02DB		0x07
+#define GAIN_04DB		0x08
+#define GAIN_06DB		0x09
+#define GAIN_08DB		0x0A
+#define GAIN_10DB		0x0B
+#define GAIN_12DB		0x0C
+#define GAIN_14DB		0x0D
+#define GAIN_16DB		0x0E
+#define GAIN_18DB		0x0F
+#define GAIN_20DB		0x10
+#define GAIN_22DB		0x11
+#define GAIN_24DB		0x12
+#define GAIN_26DB		0x13
+#define GAIN_28DB		0x14
+#define GAIN_30DB		0x15
+#define GAIN_32DB		0x16
+#define GAIN_34DB		0x17
+#define GAIN_36DB		0x18
+#define GAIN_38DB		0x19
+#define GAIN_40DB		0x1A
+#define GAIN_42DB		0x1B
+#define GAIN_44DB		0x1C
+#define GAIN_46DB		0x1D
+#define GAIN_48DB		0x1E
+#define GAIN_50DB		0x1F
+#define INPUT_MUTE		0x80
+
+/******************************************************************************
+* 
+* The POTS volume control use attenuation with 8 levels from 0dB to -28dB
+* with steps of 4dB each, the defines should be OR'ed together then sent
+* as the parameter to the mixer command to change the mixer settings.
+* 
+******************************************************************************/
+#define MIXER_PORT_POTS_PLAY	0x0F00
+
+#define POTS_ATT_00DB		0x00
+#define POTS_ATT_04DB		0x01
+#define POTS_ATT_08DB		0x02
+#define POTS_ATT_12DB		0x03
+#define POTS_ATT_16DB		0x04
+#define POTS_ATT_20DB		0x05
+#define POTS_ATT_24DB		0x06
+#define POTS_ATT_28DB		0x07
+#define POTS_MUTE		0x80
+
+/******************************************************************************
+* 
+* The DAA controls the interface to the PSTN port.  The driver loads the
+* US coefficients by default, so if you live in a different country you
+* need to load the set for your countries phone system.
+* 
+******************************************************************************/
+#define IXJCTL_DAA_COEFF_SET		_IOW ('q', 0xD0, int)
+
+#define DAA_US 		1	//PITA 8kHz
+#define DAA_UK 		2	//ISAR34 8kHz
+#define DAA_FRANCE 	3	//
+#define DAA_GERMANY	4
+#define DAA_AUSTRALIA	5
+#define DAA_JAPAN	6
+
+/******************************************************************************
+* 
+* Use IXJCTL_PORT to set or query the port the card is set to.  If the
+* argument is set to PORT_QUERY, the return value of the ioctl will
+* indicate which port is currently in use, otherwise it will change the
+* port.
+* 
+******************************************************************************/
+#define IXJCTL_PORT			_IOW ('q', 0xD1, int)
+
+#define PORT_QUERY	0
+#define PORT_POTS	1
+#define PORT_PSTN	2
+#define PORT_SPEAKER	3
+#define PORT_HANDSET	4
+
+#define IXJCTL_PSTN_SET_STATE		PHONE_PSTN_SET_STATE
+#define IXJCTL_PSTN_GET_STATE		PHONE_PSTN_GET_STATE
+
+#define PSTN_ON_HOOK	0
+#define PSTN_RINGING	1
+#define PSTN_OFF_HOOK	2
+#define PSTN_PULSE_DIAL	3
+
+/******************************************************************************
+* 
+* The DAA Analog GAIN sets 2 parameters at one time, the receive gain (AGRR), 
+* and the transmit gain (AGX).  OR together the components and pass them
+* as the parameter to IXJCTL_DAA_AGAIN.  The default setting is both at 0dB.
+* 
+******************************************************************************/
+#define IXJCTL_DAA_AGAIN		_IOW ('q', 0xD2, int)
+
+#define AGRR00DB	0x00	// Analog gain in receive direction 0dB
+#define AGRR3_5DB	0x10	// Analog gain in receive direction 3.5dB
+#define AGRR06DB	0x30	// Analog gain in receive direction 6dB
+
+#define AGX00DB		0x00	// Analog gain in transmit direction 0dB
+#define AGX_6DB		0x04	// Analog gain in transmit direction -6dB
+#define AGX3_5DB	0x08	// Analog gain in transmit direction 3.5dB
+#define AGX_2_5B	0x0C	// Analog gain in transmit direction -2.5dB
+
+#define IXJCTL_PSTN_LINETEST		_IO  ('q', 0xD3)
+
+typedef struct {
+	char month[3];
+	char day[3];
+	char hour[3];
+	char min[3];
+	int numlen;
+	char number[11];
+	int namelen;
+	char name[80];
+} IXJ_CID;
+
+#define IXJCTL_CID			_IOR ('q', 0xD4, IXJ_CID *)
+/******************************************************************************
+* 
+* The wink duration is tunable with this ioctl.  The default wink duration  
+* is 320ms.  You do not need to use this ioctl if you do not require a
+* different wink duration.
+* 
+******************************************************************************/
+#define IXJCTL_WINK_DURATION		PHONE_WINK_DURATION
+
+/******************************************************************************
+* 
+* This ioctl will connect the POTS port to the PSTN port on the LineJACK
+* In order for this to work properly the port selection should be set to
+* the PSTN port with IXJCTL_PORT prior to calling this ioctl.  This will
+* enable conference calls between PSTN callers and network callers.
+* Passing a 1 to this ioctl enables the POTS<->PSTN connection while
+* passing a 0 turns it back off.
+* 
+******************************************************************************/
+#define IXJCTL_POTS_PSTN		_IOW ('q', 0xD5, int)
+
+/******************************************************************************
+*
+* IOCTLs added by request.
+*
+* IXJCTL_HZ sets the value your Linux kernel uses for HZ as defined in
+*           /usr/include/asm/param.h, this determines the fundamental
+*           frequency of the clock ticks on your Linux system.  The kernel
+*           must be rebuilt if you change this value, also all modules you
+*           use (except this one) must be recompiled.  The default value
+*           is 100, and you only need to use this IOCTL if you use some
+*           other value.
+*
+*
+* IXJCTL_RATE sets the number of times per second that the driver polls
+*             the DSP.  This value cannot be larger than HZ.  By
+*             increasing both of these values, you may be able to reduce
+*             latency because the max hang time that can exist between the
+*             driver and the DSP will be reduced.
+*
+******************************************************************************/
+
+#define IXJCTL_HZ                       _IOW ('q', 0xE0, int)
+#define IXJCTL_RATE                     _IOW ('q', 0xE1, int)
+#define IXJCTL_FRAMES_READ		_IOR ('q', 0xE2, unsigned long)
+#define IXJCTL_FRAMES_WRITTEN		_IOR ('q', 0xE3, unsigned long)
+#define IXJCTL_READ_WAIT		_IOR ('q', 0xE4, unsigned long)
+#define IXJCTL_WRITE_WAIT		_IOR ('q', 0xE5, unsigned long)
+#define IXJCTL_DRYBUFFER_READ		_IOR ('q', 0xE6, unsigned long)
+#define IXJCTL_DRYBUFFER_CLEAR		_IO  ('q', 0xE7)
+
+/******************************************************************************
+*
+* The intercom IOCTL's short the output from one card to the input of the
+* other and vice versa (actually done in the DSP read function).  It is only
+* necessary to execute the IOCTL on one card, but it is necessary to have
+* both devices open to be able to detect hook switch changes.  The record
+* codec and rate of each card must match the playback codec and rate of
+* the other card for this to work properly.
+*
+******************************************************************************/
+
+#define IXJCTL_INTERCOM_START 		_IOW ('q', 0xFD, int)
+#define IXJCTL_INTERCOM_STOP  		_IOW ('q', 0xFE, int)
FUNET's LINUX-ADM group, [email protected]
TCL-scripts by Sam Shen (who was at: [email protected])