Unaffiliated Bidirectional Forwarding Detection (BFD) Echo

Abstract

Bidirectional Forwarding Detection (BFD) is a fault detection protocol that can quickly determine a communication failure between two forwarding engines. This document defines a use of the BFD Echo where the local system supports BFD but the adjacent system does not support BFD. BFD Control packet and its processing procedures can be executed over the BFD Echo port where the adjacent system only loops packets back to the local system.¶

This document updates RFC 5880 by defining a new method of BFD Echo-Only without requiring an implementation to support the full BFD protocol.¶

1. Introduction

To minimize the impact of device/link faults on services and improve network availability, in the single-hop cases a network device needs to be able to quickly detect faults in communication with adjacent devices. Measures can then be taken to promptly rectify the faults to ensure service continuity.¶

BFD [RFC5880] is a low-overhead, short-duration method to detect faults on the communication path between adjacent forwarding engines. The faults can be on interfaces, data links, and even the forwarding engines. It is a single, unified mechanism to monitor any media and protocol layers in real time.¶

BFD defines the Asynchronous mode and the Demand mode to satisfy various deployment scenarios. It also supports an Echo function that reduces the level of BFD support required in device implementations, as described in Section 3.2 of [RFC5880]. When the Echo function is activated, the local system sends BFD Echo packets and the remote system loops back the received Echo packets through the forwarding path. If several consecutive BFD Echo packets are not received by the local system, then the BFD session is declared to be Down.¶

When using BFD Echo function, there are two typical scenarios as below:¶

• Full BFD protocol capability with adjunct Echo function. This scenario requires both the local device and the adjacent device to support the full BFD protocol.¶

• BFD Echo-Only method without full BFD protocol capability. This scenario requires only the local device to support sending and demultiplexing BFD Control packets. In this scenario, the BFD Control packets are sent over the BFD Echo port, but that the processing procedures for Asynchronous mode are used with the modifications described in this document. Note that this method monitors the connectivity to a system over a specific interface and does not verify the availability of a specific IP address at that system.¶

The former scenario is referred to as "Affiliated BFD Echo" in this document, which remains unchanged from [RFC5880]. The latter scenario is referred to as "Unaffiliated BFD Echo", which is specified in this document.¶

Section 5 of [RFC5880] indicates that the payload of an affiliated BFD Echo packet is a local matter and hence its contents are outside the scope of that specification. This document, on the other hand, specifies the contents of the Unaffiliated BFD Echo packet and what to do with them. This would appear to contravene Section 5 of [RFC5880]. However, the core behavior in that RFC simply states that the contents of the BFD Echo packets are a local matter, and this document is simply defining "the local matter". Regarding the selection of IP address, the rules stated in Section 4 of [RFC5881] are applicable to the encapsulation of an Unaffiliated BFD Echo packet.¶

Section 6.2.2 of [BBF-TR-146] describes one use case of the Unaffiliated BFD Echo.¶

This document updates [RFC5880] by defining a new method of BFD Echo-Only without requiring an implementation to support the full BFD protocol. It specifies the use of the Unaffiliated BFD Echo over IPv4 and IPv6 for a single IP hop. A full description of the updates to [RFC5880] is provided in Section 3.¶

2. Unaffiliated BFD Echo Procedures

This section specifies the Unaffiliated BFD Echo procedures.¶

As shown in Figure 1, device A supports BFD, whereas device B does not support BFD. Device A would send Unaffiliated BFD Echo packets, and after receiving the Unaffiliated BFD Echo packets sent from device A, the one-hop-away BFD peer device B immediately loops them back by normal IP forwarding, this allows device A to rapidly detect a connectivity loss to device B. Note that device B would not intercept any received Unaffiliated BFD Echo packet or parse any BFD protocol field within the Unaffiliated BFD Echo packet.¶

An Unaffiliated BFD Echo session is not actually a BFD session because there is no coordination of BFD protocol state between the two link ends: the remote end does not support BFD and so cannot engage in a BFD session. The local end as an initiator may regard the Unaffiliated BFD Echo session as a BFD session within its implementation.¶

For unaffiliated echo, an Unaffiliated BFD Echo session is created on device A, and the Unaffiliated BFD Echo session MUST follow the BFD state machine defined in Section 6.2 of [RFC5880], except that the received state is not extracted from BFD Control packets originated by the remote system, but from packets originated by the local system and looped back from the remote system. Therefore, Unaffiliated BFD Echo does not use the AdminDown state. BFD Control packets are transmitted and received as Unaffiliated BFD Echo packets using destination UDP port 3785, as defined in [RFC5881]. The procedures for BFD Async sessions are executed for the looped BFD Control packets as per [RFC5880], including validation and authentication.¶

Once an Unaffiliated BFD Echo session is created on device A, it starts sending Unaffiliated BFD Echo packets. Unaffiliated BFD Echo packets with zeroed "Your Discriminator" field are demultiplexed to the proper session based on the source IP address or UDP source port, once the remote system loops back the local discriminator, all further received packets are demultiplexed based on the "Your Discriminator" field only, which is conform to the procedure specified in Section 6.3 of [RFC5880]. An Unaffiliated BFD Echo packet follows the same encapsulation rules as for a BFD Echo packet as specified in Section 4 of [RFC5881]. All Unaffiliated BFD Echo packets for the session MUST be sent with a Time to Live (TTL) or Hop Limit value of 255, and received with a TTL or Hop Limit value of 254, otherwise the received packets MUST be dropped.¶

Within the Unaffiliated BFD Echo packet, the "Desired Min TX Interval" and "Required Min RX Interval" defined in [RFC5880] MUST be populated with a certain value, which can avoid unset value being a potential vector for disclosure of uninitialized memory. A suggested value is 1 second (1,000,000 microseconds). These values, however, MUST be ignored on receipt. Furthermore, these values MUST NOT be used to calculate the Detection Time.¶

The "Required Min Echo RX Interval" defined in [RFC5880] MUST be populated with a certain value, which can avoid unset value being a potential vector for disclosure of uninitialized memory. A suggested value is 0. This value MUST be ignored on receipt. The transmission interval for Unaffiliated BFD Echo packets in the Up state MUST be provisioned on device A. The Unaffiliated BFD Echo feature depends on device B performing IP forwarding (actually IP redirect) functionality. While such functionality may normally be expected to be supported on a router, it may not be enabled on a host by default. The method for provisioning device B to loop back Unaffiliated BFD Echo packets is outside the scope of this document.¶

Similar to what's specified in [RFC5880], the Unaffiliated BFD Echo session begins with the periodic, slow transmission of Unaffiliated BFD Echo packets. The slow transmission rate SHOULD be no less than one second per packet, until the session is Up. After the session is Up, the provisioned transmission interval is used. When the Unaffiliated BFD Echo session goes Down, the slow transmission rate is resumed. The "Detect Mult" defined in [RFC5880] MUST be set to a value provisioned on device A. When the bfd.SessionState is Up and a "Detect Mult" number of Unaffiliated BFD Echo packets have not arrived at device A as they should, the device A "MUST set bfd.SessionState to Down and bfd.LocalDiag to 2 (Echo Function Failed)", as specified in Section 6.8.5 of [RFC5880].¶

In summary, the Unaffiliated BFD Echo packet reuses the format of the BFD Control packet defined in [RFC5880], and the fields within the Unaffiliated BFD Echo packet are populated as follows:¶

• "My Discriminator" MUST be set to the provisioned local discriminator.¶

• "Your Discriminator" MUST be set to 0 initially, and then MUST be set to the same as "My Discriminator" looped back.¶

• "Desired Min TX Interval" MUST be set to a certain value. A suggested value is 1 second (1,000,000 microseconds).¶

• "Required Min RX Interval" MUST be set to a certain value. A suggested value is 1 second (1,000,000 microseconds).¶

• "Required Min Echo RX Interval" MUST be set to a certain value. A suggested value is 0.¶

• "Detect Mult" MUST be set to the provisioned maximum allowable number of consecutively lost Unaffiliated BFD Echo packets.¶

3. Updates to RFC 5880

The Unaffiliated BFD Echo described in this document reuses the BFD Echo function as described in [RFC5880] and [RFC5881], but does not require BFD Asynchronous or Demand mode. When using the Unaffiliated BFD Echo, only the local system has the BFD protocol enabled; the remote system just loops back the received BFD Echo packets as regular data packets.¶

This document updates [RFC5880] with respect to its descriptions on the BFD Echo function as follows.¶

The 4th paragraph of Section 3.2 of [RFC5880] is updated as below:¶

• OLD TEXT
  An adjunct to both modes is the Echo function.¶

• NEW TEXT
  An adjunct to both modes is the Echo function, which can also be running independently.¶

• OLD TEXT
  Since the Echo function is handling the task of detection, the rate of periodic transmission of Control packets may be reduced (in the case of Asynchronous mode) or eliminated completely (in the case of Demand mode).¶

• NEW TEXT
  Since the Echo function is handling the task of detection, the rate of periodic transmission of Control packets may be reduced (in the case of Asynchronous mode) or eliminated completely (in the case of Demand mode). The Echo function may also be used independently, with neither Asynchronous nor Demand mode.¶

The 3rd and 9th paragraphs of Section 6.1 of [RFC5880] are updated as below:¶

• OLD TEXT
  Once the BFD session is Up, a system can choose to start the Echo function if it desires and the other system signals that it will allow it. The rate of transmission of Control packets is typically kept low when the Echo function is active.¶

• NEW TEXT
  When a system is running with Asynchronous or Demand mode, once the BFD session is Up, it can choose to start the Echo function if it desires and the other system signals that it will allow it. The rate of transmission of Control packets is typically kept low for Asynchronous mode or eliminated completely for Demand mode when the Echo function is active.¶

• OLD TEXT
  If the session goes Down, the transmission of Echo packets (if any) ceases, and the transmission of Control packets goes back to the slow rate.¶

• NEW TEXT
  In Asynchronous mode or Demand mode, if the session goes Down, the transmission of Echo packets (if any) ceases, and the transmission of Control packets goes back to the slow rate.¶

The 2nd paragraph of Section 6.4 of [RFC5880] is updated as below:¶

• OLD TEXT
  When a system is using the Echo function, it is advantageous to choose a sedate reception rate for Control packets, since liveness detection is being handled by the Echo packets. This can be controlled by manipulating the Required Min RX Interval field (see section 6.8.3).¶

• NEW TEXT
  When a system is using the Echo function with Asynchronous mode, it is advantageous to choose a sedate reception rate for Control packets, since liveness detection is being handled by the Echo packets. This can be controlled by manipulating the Required Min RX Interval field (see section 6.8.3). Note that a system operating in Demand mode would direct the remote system to cease the periodic transmission of BFD Control packets, by setting the Demand (D) bit in its BFD Control packets.¶

The 2nd paragraph of Section 6.8 of [RFC5880] is updated as below:¶

• OLD TEXT
  When a system is said to have "the Echo function active" it means that the system is sending BFD Echo packets, implying that the session is Up and the other system has signaled its willingness to loop back Echo packets.¶

• NEW TEXT
  When a system in Asynchronous or Demand mode is said to have "the Echo function active" it means that the system is sending BFD Echo packets, implying that the session is Up and the other system has signaled its willingness to loop back Echo packets.¶

The 7th paragraph of Section 6.8.3 of [RFC5880] is updated as below:¶

• OLD TEXT
  When the Echo function is active, a system SHOULD set bfd.RequiredMinRxInterval to a value of not less than one second (1,000,000 microseconds). This is intended to keep received BFD Control traffic at a negligible level, since the actual detection function is being performed using BFD Echo packets.¶

• NEW TEXT
  When the Echo function is active with Asynchronous mode, a system SHOULD set bfd.RequiredMinRxInterval to a value of not less than one second (1,000,000 microseconds). This is intended to keep received BFD Control traffic at a negligible level, since the actual detection function is being performed using BFD Echo packets. While a system operating in Demand mode would not receive BFD Control traffic.¶

The 1st and 2nd paragraphs of Section 6.8.9 of [RFC5880] are updated as below:¶

• OLD TEXT
  BFD Echo packets MUST NOT be transmitted when bfd.SessionState is not Up. BFD Echo packets MUST NOT be transmitted unless the last BFD Control packet received from the remote system contains a nonzero value in Required Min Echo RX Interval.¶

• NEW TEXT
  When a system is using the Echo function with either Asynchronous or Demand mode, BFD Echo packets MUST NOT be transmitted when bfd.SessionState is not Up, and BFD Echo packets MUST NOT be transmitted unless the last BFD Control packet received from the remote system contains a nonzero value in Required Min Echo RX Interval.¶

• OLD TEXT
  BFD Echo packets MAY be transmitted when bfd.SessionState is Up. The interval between transmitted BFD Echo packets MUST NOT be less than the value advertised by the remote system in Required Min Echo RX Interval...¶

• NEW TEXT
  When a system is using the Echo function with either Asynchronous or Demand mode, BFD Echo packets MAY be transmitted when bfd.SessionState is Up, and the interval between transmitted BFD Echo packets MUST NOT be less than the value advertised by the remote system in Required Min Echo RX Interval...¶

4. Operational Considerations

All Operational Considerations from [RFC5880] apply, except that the Unaffiliated BFD Echo can only be used across one hop, which result in unneccessity of a congestion control mechanism.¶

Some devices that would benefit from the use of BFD may be unable to support the full BFD protocol. Examples of such devices include servers running virtual machines, or Internet of Things (IoT) devices. By using Unaffiliated BFD Echo, these devices only need to support a basic loopback function.¶

As specified in Section 2 of this document, some configurations are needed to make the Unaffiliated BFD Echo work, although the configurations won't go beyond the scope of [RFC5880]. At a BFD-enabled local system, the Unaffiliated BFD Echo session can coexist with other type of BFD session, in which scenario the remote system for the Unaffiliated BFD Echo session must be different from the remote system for other type of BFD session, and the local system's discriminators for different BFD sessions must be different, at the same time it's not necessary for the local system to differentiate the Unaffiliated BFD Echo session from other type of BFD session.¶

5. Security Considerations

All Security Considerations from [RFC5880] and [RFC5881] apply.¶

Unaffiliated BFD Echo requires the remote device to loop Unaffiliated BFD Echo packets. In order to provide this service, the remote device cannot make use of Unicast Strict Reverse Path Forwarding (RPF) [RFC3704], otherwise the Unaffiliated BFD Echo packets might not pass the RPF check at the remote device.¶

As specified in Section 5 of [RFC5880], BFD Echo packets may be spoofed. Specifically for Unaffiliated BFD Echo, a DoS attacker may send spoofed Unaffiliated BFD Echo packets to the loop-back device, so some form of authentication SHOULD be included. Considering the Unaffiliated BFD Echo packets in this document are also BFD Control packets, the "Authentication Section" as defined in [RFC5880] for BFD Control packet is RECOMMENDED to be included within the Unaffiliated BFD Echo packet.¶

As stated in Section 2, in order to avoid unset values being a potential vector for disclosure of uninitialized memory, all fields of the Unaffiliated BFD Echo packet MUST be populated with a certain value, even if some of the fields are ignored on receipt.¶

6. IANA Considerations

This document has no IANA action requested.¶

7. Acknowledgements

The authors would like to acknowledge Ketan Talaulikar, Greg Mirsky, Santosh Pallagatti, Aijun Wang, Eric Vyncke, Adrian Farrel, Tim Wicinski, Dhruv Dhody, and Stephen Farrell for their careful review and very helpful comments.¶

The authors would like to acknowledge Jeff Haas for his guidance, insightful review, and very helpful comments.¶

The authors would like to acknowledge Detao Zhao for the very helpful discussion.¶

8. Contributors

Liu Aihua
ZTE
Email: [email protected]¶

Qian Xin
ZTE
Email: [email protected]¶

Zhao Yanhua
ZTE
Email: [email protected]¶

9. References